The vgabios used by bochs and qemu (and other virtualisation products)
has a bug in its implementation of INT 10,4f00 which causes the high
16 bits of %ebx and %edx to become corrupted.
The vgabios code uses a "pushaw"/"popaw" pair to preserve the low 16
bits of all non-segment registers. The vgabios code is compiled using
bcc, which generates 8086-compatible code and so never touches the
high 16 bits of the 32-bit registers. However, the function
vbe_biosfn_return_controller_information() includes the line:
size_64k = (Bit16u)((Bit32u)cur_info->info.XResolution *
cur_info->info.XResolution *
cur_info->info.BitsPerPixel) >> 19;
which generates an implicit call to the "lmulul" function. This
function is implemented in vbe.c as:
; helper function for memory size calculation
lmulul:
and eax, #0x0000FFFF
shl ebx, #16
or eax, ebx
SEG SS
mul eax, dword ptr [di]
mov ebx, eax
shr ebx, #16
ret
which modifies %eax, %ebx, and %edx (as a result of the "mul"
instruction, which places its result into %edx:%eax).
Work around this problem by marking %ebx and %edx as being clobbered
by the call to INT 10,4f00. (%eax is already used as an output
register, so does not need to be on the clobber list.)
Reported-by: Oliver Rath <rath@mglug.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for equivalent IPv4 and IPv6 settings (which requires equivalent
settings to be adjacent within the settings list).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for multiple setting definitions with the same name but
different scopes and tags. For example, allow for a "filename"
setting with default scope and tag value 67 (for DHCPv4) and a
corresponding "filename" setting with IPv6 scope and tag value 59 (for
DHCPv6).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Note that IANA has not yet assigned a DHCPv6 option code for the
syslog server. When a code is assigned, the definition of
DHCPV6_LOG_SERVERS should be updated. Until then, an IPv6 address of
a syslog server can be configured manually using e.g.
set syslog6 3ffe:302:11:2::8309
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Our policy is to prefer IPv6 addreses to IPv4 addresses, but to
request IPv6 addresses only if we have an IPv6 address for the name
server itself.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for the existence of references to IPv6 setting types without
dragging in the whole IPv6 stack, by placing the definition of
setting_type_ipv6 in core/settings.c and providing weak stub methods
for parse_ipv6_setting() and format_ipv6_setting().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The fetch_setting() family of functions may currently modify the
definition of the specified setting (e.g. to add missing type
information). Clean up this interface by requiring callers to provide
an explicit buffer to contain the completed definition of the fetched
setting, if required.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ANSI escape sequences to show and hide the cursor take the form
"<ESC>[?25h" and "<ESC>[?25l" respectively. iPXE currently treats the
'?' character as the final byte. Fix by explicitly treating '?' as an
intermediate byte.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
OpenBSD 5.4 seems to generate dynamically linked binaries by default,
which breaks our build process. Fix by forcing the linker to always
create static binaries.
Reported-by: Jiri B <jirib@devio.us>
Tested-by: Jiri B <jirib@devio.us>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There is no requirement for VBE modes to be listed in increasing order
of resolution. With the present logic, this can cause e.g. a 1024x768
mode to be selected if the user asks for 640x480, if the 1024x768 mode
is earlier in the mode list.
Define a scoring system for modes as
score = ( width * height - bpp )
and choose the mode with the lowest score among all acceptable modes.
This should prefer to choose the mode closest to the requested
resolution, with a slight preference for higher colour depths.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The VirtualBox BIOS fails to retrieve mode information (with status
0x0100) for some modes within the mode list. Skip any such modes,
rather than treating this as a fatal error.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The VESA frame buffer console uses the VESA BIOS extensions (VBE) to
enumerate video modes, selects an appropriate mode, and then hands off
to the generic frame buffer code.
The font is extracted from the VGA BIOS, avoiding the need to provide
an external font file.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the "initialising devices" message to show up on consoles which
require initialisation, by deferring it until after initialise() has
completed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for IPv6 routing table entries to be created for an on-link
prefix where a local address has not yet been assigned to the network
device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Syslinux 6.x places its files into a bios subdirectory, and requires
that a ldlinux.c32 module be included within the ISO image. Add the
relevant search paths for isolinux.bin, and include the file
ldlinux.c32 within the ISO image if it exists.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for the stateful and stateless variants of the DHCPv6
protocol. The resulting settings block is registered as
"net<x>.dhcpv6", and DHCPv6 options can be obtained using
e.g. "${net0.dhcpv6/23:ipv6}" to obtain the IPv6 DNS server address.
IPv6 addresses obtained via stateful DHCPv6 are not yet applied to the
network device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The retrieval of the cached DHCPACK and the creation of network
devices are both currently scheduled as STARTUP_NORMAL. It is
therefore possible that the cached DHCPACK will not be retrieved in
time for cachedhcp_probe() to apply it to the relevant network device.
Fix by retrieving the cached DHCPACK at initialisation time rather
than at startup time.
As an optimisation, an unclaimed cached DHCPACK can be freed
immediately after the last network device has been created, rather
than waiting until shutdown.
Reported-by: Espen Braastad <espen.braastad@redpill-linpro.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Include IPv6 within the generic network device configurator
mechanism. The IPv6 configurator will send a router solicitation and
wait for a router advertisement to be received. (As per RFC4861
section 6.3.7, we do this even if advertisements have been received
prior to sending the router solicitation.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE supports multiple mechanisms for network device configuration:
DHCPv4 for IPv4, FIP for FCoE, and SLAAC for IPv6. At present, DHCPv4
requires an explicit action (e.g. a "dhcp" command), FIP is initiated
implicitly upon opening a network device, and SLAAC takes place
whenever a RA happens to be received.
Add a generic concept of a network device configurator, which provides
a common interface to triggering configuration and to reporting the
result of the configuration process.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 5e1fa5c ("[parseopt] Add parse_timeout()") introduced a
regression causing the shell banner timeout value (calculated in
milliseconds) to be treated as a timer tick count, resulting in a
timeout of approximately two minutes rather than the intended two
seconds.
Reported-by: Christian Hesse <list@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If a job times out then use the most recent ongoing error status
reported via job_progress() (if available) as the overall return
status.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some background jobs have a meaningful ongoing status code (e.g. the
current link status for a job waiting for a network link to come up).
Allow this to be exposed via the job_progress() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If an object interface does not provide an intf_close() method, then
default to calling intf_restart(). This allows static objects to
safely ignore intf_close(), without needing to add code solely to
ensure that the interface gets unplugged.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most network upper-layer drivers do not implement all three methods
(probe, notify, and remove). Save code by making all methods
optional.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Parsing a timeout value (specified in milliseconds) into an internal
timeout value measured in timer ticks is a common operation. Provide
a parse_timeout() value to carry out this conversion automatically.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When chainloading, always retrieve the cached DHCPACK packet from the
underlying PXE stack, and apply it as the original contents of the
"net<X>.dhcp" settings block. This allows cached DHCP settings to be
used for any chainloaded iPXE binary (not just undionly.kkpxe).
This change eliminates the undocumented "use-cached" setting. Issuing
the "dhcp" command will now always result in a fresh DHCP request.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When transmitting to a link-local or multicast destination address,
use the network device's link-local address as the source address if
no explicit source address has been specified.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The IPv6 option length field represents the length of the option data
field, not the overall length of the option.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add generic pinger mechanism (analogous to the generic downloader
mechanism) which opens a ping socket, transmits ping requests, and
passes information about ping replies to a callback function.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Merge common functionality between IPv4 and IPv6 ICMP echo handling,
and add support for transmitting ICMP echo requests and delivering
ICMP echo replies to a (not yet implemented) ping_rx() function.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 238050d ("[build] Work around bug in gcc >= 4.8") works around
one instance of a bug in recent versions of gcc, in which "ebp" cannot
be specified within an asm clobber list.
Some versions of gcc seem to exhibit the same bug on other points in
the codebase. Fix by changing all instances of "ebp" in a clobber
list to use the push/pop %ebp workaround instead.
Originally-implemented-by: Víctor Román Archidona <contacto@victor-roman.es>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The path MTU is currently hardcoded to 1460 bytes, which fails to
allow space for TCP options. Sending a maximum-sized datagram (which
is viable when using HTTP POST) will therefore fail since the Ethernet
MTU will be exceeded.
Reduce the hardcoded path MTU to produce a maximum datagram of 1280
bytes, which is the size required of data link layers by IPv6. It is
a reasonable assumption that all intermediary data link layers will be
able to convey this packet without fragmentation, even for IPv4.
Note that this reduction has a minimal impact upon download
throughput, since it affects only the transmit data path.
Originally-fixed-by: Suresh Sundriyal <ssundriy@vmware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the existing partially-implemented IPv6 stack with a fresh
implementation.
This implementation is not yet complete. The IPv6 transmit and
receive datapaths are functional (including fragment reassembly and
parsing of arbitrary extension headers). NDP neighbour solicitations
and advertisements are supported. ICMPv6 echo is supported.
At present, only link-local addresses may be used, and there is no way
to specify an IPv6 address as part of a URI (either directly or via
a DNS lookup).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Split the protocol-independent portions of arp.c into a separate file
neighbour.c, to allow for sharing of functionality between IPv4+ARP
and IPv6+NDP.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
IPv6 link-local socket addresses require some way to specify a local
network device. We cannot simply use a pointer to the network device,
since a struct sockaddr_in6 may be long-lived and has no way to hold a
reference to the network device.
Using a network device index allows a socket address to cleanly refer
to a network device without worrying about whether or not that device
continues to exist.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give tap devices a meaningful name, and avoid segmentation faults when
attempting to retrieve ${net0/bustype} by assigning a new bus type for
tap devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for configurable provision of built-in settings by placing them
in a linker table rather than an array.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Prevent the card from flagging packets of 1518 bytes length as
overlength.
This fixes the High-MTU loopback test.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The 3c90x B and C revisions support rounding up the packet length to a
specific boundary. Disable this feature to avoid overlength packets.
This fixes the loopback test.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to the 3c90x datasheet we have to stall the upload (receive)
engine before setting the receive ring address.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow HTTP POST requests to be generated when the URI includes a
parameter list. For example:
#!ipxe
params
param mac ${net0/mac}
param uuid ${uuid}
param asset ${asset}
chain http://boot.ipxe.org/demo/boot.php##params
Signed-off-by: Michael Brown <mcb30@ipxe.org>
HTTP POST requires the ability to associate a parameter list with a
URI. There is no standardised syntax for this. Use a non-standard
URI syntax to incorporate the specification of a parameter list within
a URI:
URI = [ absoluteURI | relativeURI ]
[ "#" fragment ] [ "##params" [ "=" paramsName ] ]
e.g.
http://boot.ipxe.org/demo/boot.php##paramshttp://boot.ipxe.org/demo/boot.php##params=mylist
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow memory map entries to be read using the syntax
${memmap/<region>.<properties>.<scale>}
where <region> is the index of the memory region, <properties> is a
bitmask where bit 0 represents the start address and bit 1 represents
the length (allowing the end address to be encoded by having both bits
0 and 1 set), and <scale> is the number of bits by which to shift the
result.
This allows for several values of interest to be encoded. For
example:
${memmap/<region>.1.0:hexraw} # 64-bit start address of <region>
${memmap/<region>.2.0:hexraw} # 64-bit length of <region>, in bytes
${memmap/<region>.3.0:hexraw} # 64-bit end address of <region>
${memmap/<region>.2.10:int32} # Length of <region>, in kB
${memmap/<region>.2.20:int32} # Length of <region>, in MB
The numeric encoding is slightly more sophisticated than described
here, allowing a single encoding to cover multiple regions. (See the
source code for details.) The primary use case for this feature is to
provide the total system memory size (in MB) via the "memsize"
predefined setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow numeric_setting_value() to handle e.g. the byte sequence
00:00:00:00:12:34:56:78
by returning -ERANGE only if the value actually overflows the return
type.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow CPUID values to be read using the syntax
${cpuid/<register>.<function>}
For example, ${cpuid/2.0x80000001} will give the value of %ecx after
calling CPUID with %eax=0x80000001. Values for <register> are encoded
as %eax=0, %ebx=1, %ecx=2, %edx=3.
The numeric encoding is more sophisticated than described above,
allowing for settings such as the CPU model (obtained by calling CPUID
with %eax=0x80000002-0x80000004 inclusive and concatenating the values
returned in %eax:%ebx:%ecx:%edx). See the source code for details.
The "cpuvendor" and "cpumodel" settings provide easy access to these
more complex CPUID settings.
This functionality is intended to complement the "cpuid" command,
which allows for testing individual CPUID feature bits.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This makes it possible to leave UDP debugging enabled in order to see
interesting UDP events, without flooding the console with at least one
message per packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "inc" command allows the numeric value of a setting to be
incremented, allowing for the construction of simple loops within an
iPXE script.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow commands to be placed on the same line as a label. This allows
for improved legibility of loop constructions by incorporating the
loop check condition into the same line as the loop label. For
example, to iterate over network devices using the forthcoming "inc"
command:
set idx:int16 0
:loop isset ${net${idx}/mac} || goto loop_done
echo net${idx} is a ${net${idx}/chip} with MAC ${net${idx}/mac}
inc idx && goto loop
:loop_done
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Initial whitespace is already accepted on lines containing commands,
since it gets ignored by the system() call. Minimise surprise and
allow for neater indentation of scripts by also allowing whitespace on
lines containing labels.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A deliberate side effect of this commit is that the "read" command
will now preserve the type of the setting, if the setting name
contains no type information. For example:
iPXE> set foo:ipv4 192.168.0.1
iPXE> read foo
192.168.0.100
iPXE> show foo
foo:ipv4 = 192.168.0.100
rather than the arguably unexpected behaviour of resetting the type to
"string".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use parse_setting_name() and fetchf_setting_copy() in
expand_settings(), to eliminate the call to fetchf_named_setting().
This change also eliminates the potentially large stack-allocated
buffer in expand_settings().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
fetch_settings_copy() currently returns success and a NULL data
pointer to indicate a non-existent setting. This is intended to allow
the caller to differentiate between a non-existent setting and an
error in allocating memory for the copy of the setting.
The underlying settings blocks' fetch() methods provide no way to
perform an existence check separate from an attempt to fetch the
setting. A "non-existent setting" therefore means simply a setting
for which an error was encountered when attempting to fetch from every
settings block within the subtree.
Since any underlying error within a settings block (e.g. a GuestRPC
failure when attempting to retrieve a VMware GuestInfo setting) will
produce the effect of a "non-existent setting", it seems somewhat
meaningless to give special treatment to memory allocation errors
within fetch_setting_copy().
Remove the special treatment and simplify the semantics of
fetch_setting_copy() by directly passing through any underlying error
(including non-existence) encountered while fetching the setting.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There are currently two conflicting usages of the term "named setting"
within iPXE: one refers to predefined settings (such as show up in the
"config" UI), the other refers to settings identified by a name (such
as "net0.dhcp/ip").
Split these usages into the term "predefined setting" and "named
setting" to avoid ambiguity.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Our use of --gc-sections causes the linker to discard the symbols
defined by FILE_LICENCE(), meaning that the resulting licence
determination is incomplete.
We must use the KEEP() directive in the linker script to force the
linker to not discard the licence symbols. Using KEEP(*(COMMON))
would be undesirable, since there are some symbols in COMMON which we
may wish to discard.
Fix by placing symbols defined by PROVIDE_SYMBOL() (which is used by
FILE_LICENCE()) into a special ".provided" section, which we then mark
with KEEP(). All such symbols are zero-length, so there is no cost in
terms of the final binary size.
Since the symbols are no longer in COMMON, the linker will reject
symbols with the same name coming from multiple objects. We therefore
append the object name to the licence symbol, to ensure that it is
unique.
Reported-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The getopt API defines optind as a global variable. When used by the
"autoboot" command, the payload function passed to ifcommon_exec() may
result in a new iPXE script being executed; the commands therein would
then overwrite the value of optind. On returning, ifcommon_exec()
would continue processing the list of interfaces from an undefined
point.
Fix by using a local variable to hold the index within the list of
interfaces.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some hardware (observed with an onboard RTL8168) will erroneously
report a buffer overflow error if the received packet exactly fills
the receive buffer.
Fix by adding an extra four bytes of padding to each receive buffer.
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for page up, page down, home and end keys, matching the
navigation logic used in the menu user interface.
Originally-implemented-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Adrian Jamróz <adrian.jamroz@gmail.com>
Modified-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow long script lines to be broken up using backslash continuation.
For example:
choose --default linux --timeout 3000 os \
&& goto boot_${os} || goto cancelled
Requested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
base16_encode() will fail to generate a terminating NUL if the length
of the raw data is zero, since the loop calling sprintf() will never
execute.
Fix by explicitly terminating the result with a NUL.
Reported-by: Marin Hannache <git@mareo.fr>
Debugged-by: Marin Hannache <git@mareo.fr>
Tested-by: Marin Hannache <git@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the old via-rhine driver with a new version using the iPXE
API.
Includes fixes by Thomas Miletich for:
- MMIO access
- Link detection
- RX completion in RX overflow case
- Reset and EEPROM reloading
- CRC stripping
- Missing cpu_to_le32() calls
- Missing memory barriers
Signed-off-by: Adrian Jamróz <adrian.jamroz@gmail.com>
Modified-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Modified-by: Michael Brown <mcb30@ipxe.org>
Tested-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Include a sequence number as the first four bytes of the loopback test
packet payload. When a content mismatch occurs, this gives some
information about the source of the mismatched packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow any iPXE command expecting a network device name to accept
"netX" as a synonym for "most recently opened network device".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a facility for settings blocks to act as symbolic links to other
settings blocks, and reimplement the "netX" virtual settings block
using this facility.
The primary advantage of this approach is that unscoped settings such
as ${mac} and ${filename} will now reflect the settings obtained from
the most recently opened network device: in most cases, this will mean
the settings obtained from the most recent DHCP attempt. This should
improve conformance to the principle of least astonishment.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow values to be read from PCI configuration space using the syntax
${pci/<busdevfn>.<offset>.<length>}
where <busdevfn> is the bus:dev.fn address of the PCI device
(expressed as a single integer, as returned by ${net0/busloc}),
<offset> is the offset within PCI configuration space, and <length> is
the length within PCI configuration space.
Values are returned in reverse byte order, since PCI configuration
space is little-endian by definition.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Move VMWARE_SETTINGS build configuration option from config/sideband.h
to a new config/settings.h.
Existing instances of config/local/sideband.h will not be affected,
since config.c still #includes config/sideband.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow network device's "busloc" setting to be formatted as a PCI
bus:dev.fn address using e.g. ${net0/busloc:busdevfn}.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hex_decode() to parse "hex" and "hexhyp" settings. Note that this
parser is stricter than the old parser; it now requires exactly two
hex digits for each byte. (The old parser was based upon strtoul()
and so would allow leading whitespace and a leading plus or minus
sign.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a generic hex_decode() routine which can be shared between the
Base16 code and the "hex" and "hexhyp" settings parsers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On large networks with substantial numbers of monitoring agents,
unwanted TCP connection attempts may end up flooding iPXE's ARP cache.
Fix by silently dropping packets received for unrecognised TCP
connections. This should not cause problems, since many firewalls
will also silently drop any such packets.
Reported-by: Jarrod Johnson <jarrod.b.johnson@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Locate the settings block containing the filename, and search only
that settings block for the next-server address. This avoids problems
caused by misconfigured DHCP servers which provide a next-server
address (often defaulting to the DHCP server's own IP address) even
when not providing a filename.
Originally-implemented-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
gcc 4.8 and 4.9 fail to compile pxe_call.c with the error "bp cannot
be used in asm here". Other points in the codebase which use "ebp" in
the asm clobber list do not seem to be affected.
Unfortunately gcc provides no way to specify %ebp as an output
register, so we cannot use this as a workaround. The only viable
solution is to explicitly push/pop %ebp within the asm itself. This
is ugly for two reasons: firstly, it may be unnecessary; secondly, it
may cause gcc to generate invalid %esp-relative addresses if the asm
happens to use memory operands. This specific block of asm uses no
memory operands and so will not generate invalid code.
Reported-by: Daniel P. Berrange <berrange@redhat.com>
Reported-by: Christian Hesse <list@eworm.de>
Originally-fixed-by: Christian Hesse <list@eworm.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of Linux apparently complain if initrds are not aligned
to a page boundary. Fix by changing INITRD_ALIGN from 4 bytes to 4096
bytes.
The amount of padding at the end of each initrd will now often be
sufficient to allow the cpio header to be prepended without crossing
an alignment boundary. The final location of the initrd may therefore
end up being slightly higher than the post-shuffle location.
bzimage_load_initrd() must therefore now copy the initrd body prior to
copying the cpio header, otherwise the start of the initrd body may be
overwritten by the cpio header. (Note that the guarantee that an
initrd will never need to overwrite an initrd at a higher location
still holds, since the overall length of each initrd cannot decrease
as a result of adding a cpio header.)
Reported-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
RFC2560 mandates that a valid OCSP response will contain exactly one
relevant certificate. However, some OCSP responders include
extraneous certificates. iPXE currently assumes that the first
certificate in the OCSP response is the relevant certificate; OCSP
checks will therefore fail if the responder includes the extraneous
certificates before the relevant certificate.
Fix by using the responder ID to identify the relevant certificate.
Reported-by: Christian Stroehmeier <stroemi@mail.uni-paderborn.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
realtek_destroy_ring() currently does nothing if the card is operating
in legacy (pre-RTL8139C+) mode. In particular, the producer and
consumer counters are incorrectly left holding their current values.
Virtual hardware (e.g. the emulated RTL8139 in qemu and similar VMs)
is tolerant of this behaviour, but real hardware will fail to transmit
if the descriptors are not used in the correct order.
Fix by resetting the producer and consumer counters in
realtek_destroy_ring() even if the card is operating in legacy mode.
Reported-by: Gelip <mrgelip@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 2422647 ("[prefix] Allow prefix to specify an arbitrary maximum
address for relocation") introduced a regression into the UNDI ROM
loader by preserving an extra register on the stack without modifying
the %sp-relative addresses used in the routine.
Fix by correcting the %sp-relative addresses to allow for the extra
preserved variable.
Signed-off-by: Frediano Ziglio <frediano.ziglio@citrix.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When the $(eval) function is available (in GNU make >= 3.80), we can
evaluate many of the dynamically-generated Makefile rules directly.
This avoids generating a few hundred Makefile fragments in the
filesystem, and so speeds up the build process.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If a certificate chain contains no certificate which can be validated
as a standalone certificate (i.e. contains no trusted root
certificates or previously-validated certificates) then iPXE will
currently return a fixed error EACCES_UNTRUSTED. This masks the
actual errors obtained when attempting to validate each certificate as
a standalone certificate, and so makes troubleshooting difficult for
the end user.
Fix by instead returning the error obtained when attempting to
validate the final certificate in the chain as a standalone
certificate. This error is most likely (though not guaranteed) to
represent the "real" problem.
Reported-by: Sven Dreyer <sven@dreyer-net.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Extend the syntax for numerical SMBIOS settings from
smbios/<type>.<offset>.<length>
to
smbios/[<instance>.]<type>.<offset>.<length>
Where SMBIOS provides multiple structures with the same <type>, this
extended syntax allows for access to structures other than the first.
If <instance> is omitted then it will default to zero, giving access
to the first instance (and so matching existing behaviour).
The 16-bit SMBIOS handle (which is an alternative way to disambiguate
multiple instances of the same type of structure) can be accessed, if
required, using
smbios/<instance>.<type>.2.2:uint16
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE allows access to general SMBIOS settings using the syntax:
smbios/<type>.<offset>.<length>
This provides access to any fixed-offset field within an SMBIOS
structure. This syntax is currently overloaded to interpret a zero
<length> as meaning that the byte at <offset> contains a string index;
this provides access to SMBIOS strings (which are not located at fixed
offsets).
The "OEM Strings" SMBIOS structure contains strings which are not
referenced by any fixed string index field within the structure. iPXE
currently provides no way to access these strings.
Fix by overloading the syntax for numerical SMBIOS settings to
interpret an <offset> of zero as implying that <length> contains a
literal string index. The OEM Strings can then be accessed using:
smbios/11.0.1
smbios/11.0.2
smbios/11.0.3
...
The actual byte at offset zero will always contain the structure type,
which is already known since it must be specified in order to access
the structure. There is thus no plausible existing use case for an
offset of zero; overloading the syntax in this way should therefore
not break compatibility with any existing scripts.
The corner case where both <offset> and <length> are zero is undefined
(and, for now, will simply return a "not found" error).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Create an explicit concept of "settings scope" and eliminate the magic
values used for numerical setting tags.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Devices with small transmit descriptor rings may temporarily run out
of space. Provide netdev_tx_defer() to allow drivers to defer packets
for retransmission as soon as a descriptor becomes available.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some systems, it appears to be possible for writes to the EEPROM
registers to be delayed for long enough that the EEPROM's setup and
hold times are violated, resulting in invalid data being read from the
EEPROM.
Fix by inserting a PCI read cycle immediately after writes to
RTL_9346CR, to ensure that the write has completed before starting the
udelay() used to time the SPI bus transitions.
Reported-by: Gelip <mrgelip@gmail.com>
Tested-by: Gelip <mrgelip@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Report the cause of the failure when we are unable to open the .mrom
payload. There are two possible failure cases:
- Unable to find a suitable memory BAR to borrow (e.g. if the NIC
doesn't have a memory BAR that is at least as large as the
expansion ROM BAR, or if the memory BAR has been assigned a 64-bit
address which won't fit into the 32-bit expansion ROM BAR). This
will be reported as "BABABABA".
- Unable to find correct ROM image within the BAR. This will be
reported as the address (within the borrowed BAR) at which we first
fail to find a valid 55AA signature.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older RTL8139 chips seem to not immediately update the
RTL_CR.BUFE bit in response to a write to RTL_CAPR. This results in
iPXE seeing a spurious zero-length received packet, and thereafter
being out of sync with the hardware's RX ring offset.
Fix by inserting an extra PCI read cycle after writing to RTL_CAPR, to
give the chip time to react before we next read RTL_CR.
Reported-by: Gelip <mrgelip@gmail.com>
Tested-by: Gelip <mrgelip@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some onboard RTL8169 NICs seem to leave the EEPROM pins disconnected.
The existing is_valid_ether_addr() test will not necessarily catch
this, since it expects a missing EEPROM to show up as a MAC address of
00:00:00:00:00:00 or ff:ff:ff:ff:ff:ff. When the EEPROM pins are
floating the MAC address may read as e.g. 00:00:00:00:0f:00, which
will not be detected as invalid.
Check the ID word in the first two bytes of the EEPROM (which should
have the value 0x8129 for all RTL8139 and RTL8169 chips), and use this
to determine whether or not an EEPROM is present.
Reported-by: Carl Karsten <carl@nextdayvideo.com>
Tested-by: Carl Karsten <carl@nextdayvideo.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
sparse does not understand -fshort-wchar. Default to using uint16_t
as a wchar_t if not explicitly specified by the compiler, to avoid
large numbers of spurious warnings from sparse.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Linker table entries must be non-static in order to avoid being
completely optimised away by some versions of gcc. Use -Wno-decl to
prevent sparse from warning about these, since the alternative would
be to litter the code with otherwise unnecessary "extern"
declarations.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
sparse does not define __WCHAR_TYPE__ or __WINT_TYPE__. We already
define __WCHAR_TYPE__ if the compiler does not do so; do the same for
__WINT_TYPE__.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
sparse seems to have problems finding compiler.h when specified as
"-include compiler.h"; one possible explanation is that it ignores the
include path. Fix by using "-include include/compiler.h".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently seeds the random number generator using the system
timer tick count. When large numbers of machines are booted
simultaneously, multiple machines may end up choosing the same DHCP
transaction ID (XID) value; this can cause problems.
Fix by using the least significant (and hence most variable) bits of
each network device's link-layer address to perturb the random number
generator. This introduces some per-machine unique data into the
random number generator's seed, and so reduces the chances of DHCP XID
collisions.
This does not affect the ANS X9.82-compatible random bit generator
used by TLS and other cryptography code, which uses an entirely
separate source of entropy.
Originally-implemented-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add disambiguated errors for LoadImage() and StartImage(), primarily
to demonstrate how to use __einfo_uniqify() and __einfo_platformify()
in the context of EFI platform errors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Exploit the redefinition of iPXE error codes to include a "platform
error code" to allow for meaningful conversion of EFI_STATUS values to
iPXE errors and vice versa.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The low 8 bits of an iPXE error code are currently defined as the
closest equivalent PXE error code. Generalise this scheme to
platforms other than PC-BIOS by extending this definition to "closest
equivalent platform error code". This allows for the possibility of
returning meaningful errors via EFI APIs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Intel 10 Gigabit NICs have a datapath that is almost
register-compatible with the Intel 1 Gigabit NICs. Expose common
functionality to avoid duplication of code in the new "intelx" driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Intel 10 Gigabit NICs use the same simplified (aka "legacy")
descriptor format and the same layout for descriptor register blocks
as the Intel 1 Gigabit NICs. The offsets of the descriptor register
blocks are not the same.
Simplify reuse of the existing code by removing all hardcoded offsets
for registers within descriptor register blocks, and ensuring that all
offsets are calculated using the descriptor register block base
address provided via intel_init_ring().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The implementation of INT 10,06 on some BIOSes (observed with both
Hyper-V and a Dell OptiPlex 7010) seems to treat %dx=0xffff as a
special value meaning "do absolutely nothing". Fix by using
%dx=0xfefe, which should still be sufficient to cover any realistic
screen size.
Reported-by: John Clark <skyman@iastate.edu>
Tested-by: John Clark <skyman@iastate.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose the build architecture (e.g. "i386" or "x86_64") via
${buildarch} and the firmware platform (e.g. "pcbios" or "efi") via
${platform}. These settings directly expose the ARCH and PLATFORM
variables from the Makefile.
Note that the build architecture reflects the architecture for which
iPXE was compiled, not the architecture on which iPXE is currently
running. The "cpuid" command can be used to detect a 64-bit system at
runtime.
Requested-by: James A. Peltier <jpeltier@sfu.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid using UINT16 and similar typedefs, which are non-standard in the
iPXE codebase and generate conflicts when trying to include any of the
EFI headers.
Also fix trailing whitespace in the affected files, to prevent
complaints from git.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove macros which aren't used anywhere in the driver, and which
conflict with macros of the same name used in the EFI headers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove macros which aren't used anywhere in the driver, and which
conflict with macros of the same name used in the EFI headers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Abstract out the ability to reboot the system to a separate reboot()
function (with platform-specific implementations), add an EFI
implementation, and make the existing "reboot" command available under
EFI.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The PXE spec does not specify a byte ordering for UUIDs, but RFC4578
suggests that it follows the EFI spec, in which the first three fields
are little-endian.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE treats UUIDs as being in network byte order (big-endian). The
SMBIOS specification version 2.6 states that UUIDs are stored with
little-endian values in the first three fields; earlier versions did
not specify an endianness. This results in some inconsistency between
the BIOS, vendor PXE, iPXE, and operating system interpretations of
the SMBIOS UUID.
dmidecode assumes that the byte order is little-endian if and only if
the SMBIOS version is 2.6 or higher. Choose to match this behaviour.
Reported-by: Matthew Helton <mwhelton@gmail.com>
Reported-by: Alexandru Bordei <alexandru.bordei@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 2629b7e ("[pcbios] Inhibit all calls to INT 15,e820 and INT
15,e801 during POST") introduced a regression into .lkrn images when
used with no corresponding initrd.
Specifically, the semantics of the "maximum address for relocation"
value passed to install_prealloc() in %ebp changed so that zero became
a special value meaning "inhibit use of INT 15,e820 and INT 15,e801".
The %ebp value meaing "no upper limit on relocation" was changed from
zero to 0xffffffff, and all prefixes providing fixed values for %ebp
were updated to match the new semantics.
The .lkrn prefix provides the initrd base address as the maximum
address for relocation. When no initrd is present, this address will
be zero, and so will unintentionally trigger the "inhibit INT 15,e820
and INT 15,e801" behaviour.
Fix by explicitly setting %ebp to 0xffffffff if no initrd is present
before calling install_prealloc().
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Tested-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Newer versions of bfd.h require definitions for the PACKAGE and
PACKAGE_VERSION macros used by autotools. Work around this by
manually defining these macros before including bfd.h.
Originally-fixed-by: Brandon Penglase <bpenglase-ipxe@spaceservices.net>
Tested-by: Brandon Penglase <bpenglase-ipxe@spaceservices.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When iPXE is used as a UEFI driver, the UEFI PXE base code currently
provides the TCP/IP stack, network protocols, and user interface.
This represents a substantial downgrade from the standard BIOS iPXE
user experience.
Fix by installing our own EFI_LOAD_FILE_PROTOCOL implementation which
initiates the standard iPXE boot procedure. This upgrades the UEFI
iPXE user experience to match the standard BIOS iPXE user experience.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose iPXE's images as a UEFI file system, allowing the booted image
to access all images downloaded by iPXE.
This functionality is complementary to the custom iPXE download
protocol. The iPXE download protocol allows a booted image to utilise
iPXE to download arbitrary URIs, but requires the booted image to
specifically support the custom iPXE download protocol. The new
functionality limits the booted image to accessing only files that
were already downloaded by iPXE (e.g. as part of a script), but can
work with any generic UEFI image (e.g. the UEFI shell). Both
protocols are provided simultaneously, and are attached to the SNP
device handle.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If a multifunction PCI device exposes an iPXE ROM via each function,
then each function will display a "Press Ctrl-B to configure iPXE"
prompt, and delay for two seconds. Since a single instance of iPXE
can drive all functions on the multifunction device, this simply adds
unnecessary delay to the boot process.
Fix by inhibiting the "Press Ctrl-B" prompt for all except the first
function on a PCI device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Many BIOSes do not construct the full system memory map until after
calling the option ROM initialisation entry points. For several
years, we have added sanity checks and workarounds to accommodate
charming quirks such as BIOSes which report the entire 32-bit address
space (including all memory-mapped PCI BARs) as being usable RAM.
The IBM x3650 takes quirky behaviour to a new extreme. Calling either
INT 15,e820 or INT 15,e801 during POST doesn't just get you invalid
data. We could cope with invalid data. Instead, these nominally
read-only API calls manage to trash some internal BIOS state, with the
result that the system memory map is _never_ constructed. This tends
to confuse subsequent bootloaders and operating systems.
[ GRUB 0.97 fails in a particularly amusing way. Someone thought it
would be a good idea for memcpy() to check that the destination memory
region is a valid part of the system memory map; if not, then memcpy()
will sulk, fail, and return NULL. This breaks pretty much every use
of memcpy() including, for example, those inserted implicitly by gcc
to copy non-const initialisers. Debugging is _fun_ when a simple call
to printf() manages to create an infinite recursion, exhaust the
available stack space, and shut down the CPU. ]
Fix by completely inhibiting calls to INT 15,e820 and INT 15,e801
during POST.
We do now allow relocation during POST up to the maximum address
returned by INT 15,88 (which seems so far to always be safe). This
allows us to continue to have a reasonable size of external heap, even
if the PMM allocation is close to the 1MB mark.
The downside of allowing relocation during POST is that we may
overwrite PMM-allocated memory in use by other option ROMs. However,
the downside of inhibiting relocation, when combined with also
inhibiting calls to INT 15,e820 and INT 15,e801, would be that we
might have no external heap available: this would make booting an OS
impossible and could prevent some devices from even completing
initialisation.
On balance, the lesser evil is probably to allow relocation during
POST (up to the limit provided by INT 15,88). Entering iPXE during
POST is a rare operation; on the even rarer systems where doing so
happens to overwrite a PMM-allocated region, then there exists a
fairly simple workaround: if the user enters iPXE during POST and
wishes to exit iPXE, then the user must reboot. This is an acceptable
cost, given the rarity of the situation and the simplicity of the
workaround.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
romprefix.S currently calls uninstall() with an invalid value in %ax.
Consequently, base memory is not freed after a ROM boot attempt (or
after entering iPXE during POST).
The uninstall() function is physically present in .text16, and so can
use %cs to determine the .text16 segment address. The .data16 segment
address is not required, since uninstall() is called only by code
paths which set up .data16 to immediately follow .text16.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add "make vmware" build target, to build all of the ROMs used with
VMware.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The PXE TFTP API allows the caller to request a particular TFTP block
size. Since mid-2008, iPXE has appended a "?blksize=xxx" parameter to
the TFTP URI constructed internally; nothing has ever parsed this
parameter. Nobody seems to have cared that this parameter has been
ignored for almost five years.
Fix by using xfer_window(), which provides a fairly natural way to
convey the block size information from the PXE TFTP API to the TFTP
protocol layer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Nothing currently prevents a menu separator from being assigned a
shortcut key, and then from being selected using that shortcut key.
This produces an inconsistency in the user interface, since separators
cannot be selected by other means of menu navigation (arrow keys, page
up/down, etc).
It would be trivial to prevent separators from being assigned shortcut
keys, but this would eliminate one potentially useful use case: having
a large menu and using shortcut keys to jump to a section within the
menu.
Fix by treating a shortcut key on a separator as equivalent to "select
the separator, then press the down arrow key". This has the effect of
moving to the first non-separator menu item following the specified
separator, which is probably the most intuitive behaviour. (The
existing logic for moving the selection already handles the various
nasty corner cases such as a menu ending with one or more separators.)
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Unrecognised keys may be returned by getkey() as character code zero,
which currently matches against the first menu item with no shortcut
key defined.
Prevent this unintended behaviour by explicitly checking that the menu
item has a defined shortcut key.
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The output->buf field is a pointer, not an array, so sizeof() is not
applicable. We must use the allocated string length instead.
Identified by gcc:
util/zbin.c: In function ‘alloc_output_file’:
util/zbin.c:146:37: warning: argument to ‘sizeof’ in ‘memset’ call
is the same expression as the destination; did you mean to
dereference it? [-Wsizeof-pointer-memaccess]
memset ( output->buf, 0xff, sizeof ( output->buf ) );
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some PXE stacks are known to claim that IRQs are supported, but then
never generate interrupts. No satisfactory solution has been found to
this problem; the workaround is to add the PCI vendor and device IDs
to a list of devices which will be treated as simply not supporting
interrupts.
This is something of a hack, since it will generate false positives
for identical devices with a working PXE stack (e.g. those that have
been reflashed with iPXE), but it's an improvement on the current
situation.
Reported-by: Richard Moore <rich@richud.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some NICs (e.g. Hermon) provide hardware support for stripping the
VLAN tag, but do not provide any way for this support to be disabled.
Drivers for this hardware must therefore call vlan_find() to identify
a suitable receiving network device.
Provide a weak version of vlan_find() which will always return NULL if
VLAN support has not been enabled (either directly, or by enabling
a feature such as FCoE which requires VLAN support). This allows the
VLAN code to be omitted from builds where the user has not requested
support for VLANs.
Inspired-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iBFT NIC section has a VLAN field which must be filled in so that
iSCSI booting works over VLANs.
Unfortunately it is unclear from the IBM specification linked in
ibft.c whether the VLAN field is just the 802.1Q VLAN Identifier or
the full 802.1Q TCI. For now just fill in the VID, the Priority Code
Point and Drop Eligible Indicator could be set in the future if it
turns out they should be present too.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iBFT has a VLAN field that should be filled in. Add the
vlan_tag() function to extract the VLAN tag of a network device.
Since VLAN support is optional, define a weak function that returns 0
when iPXE is built without VLAN support.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Authenticode requires that the size of the raw file must equal the
size of the OptionalHeader.SizeOfHeaders plus the sum of all sections'
SizeOfRawData.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow non-data records to be split across multiple received I/O
buffers, to accommodate large certificate chains.
Reported-by: Nicola Volpini <Nicola.Volpini@kambi.com>
Tested-by: Nicola Volpini <Nicola.Volpini@kambi.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EFI's device naming model requires drivers to provide names for child
devices. Allow the driver's GetControllerName() method to delegate to
an instance of EFI_COMPONENT_NAME2_PROTOCOL installed on the child
device itself (if present); this allows the SNP device to expose its
own device name via the PCI driver's GetControllerName() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At present, loading a bzImage via iPXE requires enough RAM to hold two
copies of each initrd file. Remove this constraint by rearranging the
initrds in place.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No code from the original source remains within this file; relicense
under GPL2+ with a new copyright notice.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The version number string is currently updated only if version.o
happens to be rebuilt due to changes in its dependencies. Add a
dependency upon the git index, so that the version number is updated
after any checkout.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Using -fno-dwarf2-cfi-asm is not sufficient to prevent the .eh_frame
section from being generated on newer versions of gcc. Add
-fno-exceptions -fno-unwind-tables -fno-asynchronous-unwind-tables;
this is sufficient to inhibit the .eh_frame section on gcc 4.7.1.
This does not affect the overall binary size, but does fix the numbers
reported by "size" for individual object files.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Current versions of gcc require -maccumulate-outgoing-args if any
sysv_abi functions call ms_abi functions. This requirement is likely
to be lifted in future gcc versions, so test explicitly to see if the
current version of gcc requires -maccumulate-outgoing-args.
This problem is currently masked since the implied
-fasynchronous-unwind-tables (which is the default in current gcc
versions) implies -maccumulate-outgoing-args.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 947976d ("[netdevice] Do not force a poll on net_tx()")
requires network devices to have TX rings that are sufficiently large
to allow a transmitted response to all packets received during a
single poll.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Intel NIC emulation in some versions of VMware seems to suffer
from a flaw whereby the Interrupt Cause Register (ICR) fails to assert
the usual "packet received" bit (ICR.RXT0) if a receive overflow
(ICR.RXO) has also occurred.
Work around this flaw by polling for completed descriptors whenever
either ICR.RXT0 or ICR.RXO is asserted.
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Debugged-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Tested-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid memory leaks by clearing any (non-child) settings immediately
before unregistering the network device settings block.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When prompting the user to enter a setting value via the "read"
command, prefill the input buffer with the setting's current value.
Requested-by: Ján Ondrej (SAL) <ondrejj@salstar.ks>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Including a netdev_poll() within net_tx() can cause the net_step()
loop to end up processing hundreds or thousands of packets within a
single step, since each received packet being processed may trigger a
response which, in turn causes a poll for further received packets.
Network devices must now ensure that the TX ring is at least as large
as the RX ring, in order to avoid running out of TX descriptors. This
should not cause any problems; unlike the RX ring, there is no
substantial memory cost incurred by increasing the TX ring size.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the newline from the "Press Ctrl-B..." prompt string, so that
prompt() does not attempt to backspace beyond the start of the line.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 5ad445f ("[settings] Treat an empty formatted value as meaning
"delete setting"") (re)defined the semantics of storing an empty
formatted setting as meaning "delete setting".
Remove the existing self-test using an empty formatted hex setting
value, since it no longer conforms to the defined semantics.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Take ownership from the ARP cache at the start of arp_destroy(), to
ensure that no code path can lead to arp_destroy() being re-entered.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
serial_console_init() would enable serial console support without
knowing if the serial driver succeeded or not. As a result, the
serial console would interfere with a normal keyboard on a system
lacking serial support.
Reported-by: Jan ONDREJ (SAL) <ondrejj(at)salstar.sk>
Signed-off-by: Shao Miller <sha0.miller@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 73eb3f1 ("[int13] Zero all possible registers when jumping to a
boot sector") introduced a regression preventing the SAN-booting of
boot sectors which rely upon %dl containing the correct drive number
(such as most CD-ROM boot sectors).
Fix by not zeroing %edx.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
TLS servers are not obliged to implement the RFC3546 maximum fragment
length extension, and many common servers (including OpenSSL, as used
in Apache's mod_ssl) do not do so. iPXE may therefore have to cope
with TLS records of up to 16kB. Allocations for 16kB have a
non-negligible chance of failing, causing the TLS connection to abort.
Fix by maintaining the received record as a linked list of I/O
buffers, rather than a single contiguous buffer. To reduce memory
pressure, we also decrypt in situ, and deliver the decrypted data via
xfer_deliver_iob() rather than xfer_deliver_raw().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
eIPoIB requires space to expand a transmitted ARP packet. This
guarantee is met by ensuring that a transmitted packet consists of at
least MAX_LL_HEADER_LEN bytes from the start of the I/O buffer up to
the end of the link-layer header, and at least IOB_ZLEN bytes
thereafter.
Adjust the I/O buffer allocation for SNP transmitted packets to ensure
that this guarantee is met.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At least one boot sector (the DUET boot sector used for bootstrapping
EFI from a non-EFI system) fails to initialise the high words of
registers before using them in calculations, leading to undefined
behaviour.
Work around such broken boot sectors by explicitly zeroing the
contents of all registers apart from %cs:%ip and %ss:%sp.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When fetching a named setting using a name that does not explicitly
specify a type, default to using the type stored when the setting was
created, rather than always defaulting to "string". This allows the
behaviour of user-defined settings to match the behaviour of
predefined settings (which have a sensible default type).
For example:
set server:ipv4 192.168.0.1
echo ${server}
will now print "192.168.0.1", rather than trying to print out the raw
IPv4 address bytes as a string.
The downside of this change is that existing tricks for printing
special characters within scripts may require (backwards-compatible)
modification. For example, the "clear screen" sequence:
set esc:hex 1b
set cls ${esc}[2J
echo ${cls}
will now have to become
set esc:hex 1b
set cls ${esc:string}[2J # Must now explicitly specify ":string"
echo ${cls}
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Almost all clients of the raw-packet interfaces (UNDI and SNP) can
handle only Ethernet link layers. Expose an Ethernet-compatible link
layer to local clients, while remaining compatible with IPoIB on the
wire. This requires manipulation of ARP (but not DHCP) packets within
the IPoIB driver.
This is ugly, but it's the only viable way to allow IPoIB devices to
be driven via the raw-packet interfaces.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for allocation of memory blocks having a specified offset from a
specified physical alignment, such as being 12 bytes before a 2kB
boundary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards seem to drive the EEPROM CS line high (i.e. active)
when 9346CR.EEM is set to "normal operating mode", with the result
that the CS line is never deasserted. The symptom of this is that the
first read from the EEPROM will work, while all subsequent reads will
return garbage data.
Reported-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up advertising
only 100Mbps, despite being capable of 1000Mbps. Forcibly enable
advertisement of 1000Mbps on any RTL8169-like card.
This change relies on the assumption that the CTRL1000 register will
not exist on 100Mbps-only RTL8169 cards such as the RTL8101.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) crash and burn if DAC
is enabled, even if only 32-bit addresses are used. Observed
behaviour includes system lockups and repeated transmission of garbage
data onto the wire.
This seems to be a known problem. The Linux r8169 driver disables DAC
by default and provides a "use_dac" module parameter.
There appears to be no known test for determining whether or not DAC
will work. As a workaround, enable DAC only if we are built as as
64-bit binary. This at least eliminates the problem in the common
case of a 32-bit build, which will never use 64-bit addresses anyway.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some bits in the C+ Command register are always one. Testing for the
presence of the register must allow for this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with
TCR.MXDMA set to 16 bytes. While this does not prevent proper
operation, it almost certainly degrades performance.
Fix by explicitly setting TCR.MXDMA to "unlimited".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with invalid
values in RCR.RXFTH and RCR.MXDMA, causing receive DMA to fail. Fix
by setting explicit values for both fields.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with garbage
values in the ring address registers, and do not clear the registers
on reset.
Fix by always setting the high dword of the ring address registers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 501527d ("[http] Treat any unexpected connection close as an
error") introduced a regression causing HTTP SAN booting to fail. At
the end of the response to the HEAD request, the call to http_done()
would erroneously believe that the server had disconnected in the
middle of the HTTP headers.
Fix by treating the header block from a HEAD request as a trailer
block. This fixes the problem and also simplifies the logic in
http_rx_header().
Reported-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The FTP SIZE command allows us to get the size of a particular file,
as a consequence, we can now show proper transfer progression while
fetching a file using the FTP protocol.
Signed-off-by: Marin Hannache <git@mareo.fr>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently checks that the server has not closed the connection
mid-stream (i.e. in the middle of a chunked transfer, or before the
specified Content-Length has been received), but does not check that
the server got as far as starting to send data. Consequently, if the
server closes the connection before any data is transferred (e.g. if
the server gives up waiting while iPXE performs the validation steps
for TLS), then iPXE will treat this as a successful transfer of a
zero-length file.
Fix by checking the RX connection state, and forcing an error if the
server has closed the connection at an unexpected point.
Originally-fixed-by: Marin Hannache <mareo@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown