Very nasty things can happen if a NULL network device is used. Check
that pxe_netdev is non-NULL at the applicable entry points, so that
this type of problem gets reported to the caller rather than being
allowed to crash the system.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
It can sometimes be awkward to prevent additional packets from being
received during a loopback test. Allow such additional packets to be
present without terminating the test.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On at least one PXE stack (Realtek r8169), PXENV_UNDI_INITIALIZE has
been observed to fail intermittently due to a media test failure (PXE
error 0x00000061). Retrying the call to PXENV_UNDI_INITIALIZE
succeeds, and the NIC is then usable.
It is worth noting that this particular Realtek PXE stack is already
known to be unreliable: for example, it repeatably fails its own
boot-time media test after every warm reboot.
Fix by attempting PXENV_UNDI_INITIALIZE multiple times, with a short
delay between each attempt to allow the link to settle.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The PXE specification requires us to request DHCP options 128 to 135
inclusive, although these have no defined purpose.
Suggested-by: Ralf Buettner <rab@bootix.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The RS bit is used to instruct the NIC to update the TX descriptor
status byte. The RPS bit is used to instruct the NIC to defer this
update until after the packet has been transmitted on the wire (rather
than merely read into the transmit FIFO).
The driver currently sets RPS but not RS. Some e1000 models seem to
interpret this as implying that the status byte should be updated;
some don't. On the ones that don't, we never see any TX completions
and so rapidly run out of TX buffers.
Fix by setting the RS bit in the TX descriptor. (We don't care about
when the packet reaches the wire, so don't bother setting the RPS
bit.)
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some iSCSI targets (observed with stgt) can be configured to reject
connections that do not use header or data digests, and will respond
with "HeaderDigest=Reject" and/or "DataDigest=Reject", while still
allowing the connection to proceed to the full feature phase.
According to a strict reading of RFC3720, we are perfectly safe to
ignore these "Reject" messages: upon such a rejection "the negotiated
key is left at its current value (or default if no value was set)".
Since the default value for both HeaderDigest and DataDigest is
"None", then the only viable conclusion to be drawn is that the value
resulting from "Reject" is still "None".
Unfortunately, stgt doesn't seem to agree with this interpretation of
events, causing us to eventually report an unhelpful "connection timed
out" message to the user when we don't get any response to our first
PDU in full feature phase.
Fix by detecting any rejected parameters and immediately reporting an
error, which at least gives the user some insight as to what the real
problem may be.
Reported-by: Michal Suchanek <hramrach@centrum.cz>
Tested-by: Michal Suchanek <hramrach@centrum.cz>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 9b99d2a ("[build] Avoid generating ROMs with "match-any" vendor
or device IDs") introduced a regression which caused the UNDI PCI
driver to be omitted from the list of all drivers, and thus to be
excluded from the all-drivers build.
Fix by ensuring that the per-driver section of the Makefile is
generated even when there are no ROMs to be built.
Reported-by: Sven Dreyer <sven@dreyer-net.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
WinPE has been observed to call PXENV_UNDI_SHUTDOWN but not
PXENV_STOP_UNDI. This means that Hermon hardware is left partially
active (firmware running and one event queue mapped) when WinPE starts
up, which can cause a Blue Screen of Death.
Fix by ensuring that the hardware is left quiescent (with the firmware
stopped) when no interfaces are open.
Reported-by: Itay Gazit <itayg@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid spurious matches for peer key 0 against empty peer cache
entries, and set the LL_MULTICAST flag in addition to LL_BROADCAST.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ChipCmd register is only an 8-bit register. The 16-bit access
used by iPXE was causing an issue when used with qemu emulated rtl8139
device which was improperly aligning IOs.
Signed-off-by: Julian Pidancet <julian.pidancet@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow an initrd (such as an embedded script) to be passed to iPXE when
loaded as a .lkrn (or .iso) image. This allows an embedded script to
be varied without recompiling iPXE.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Specify a driver name of "undionly" and a device name based on the
UNDI-reported underlying hardware device. For example:
net0: 52:54:00:12:34:56 using undionly on UNDI-PCI00:03.0 (open)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Drivers are currently expected to initialise only the hardware
address, with the link-layer protocol code taking care of converting
this into a valid link-layer address. Some drivers (e.g. undinet) can
legitimately determine both the hardware and link-layer addresses,
which may differ.
Allow for this situation by checking to see if the link-layer address
is empty before initialising it from the hardware address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some BIOSes are reported to corrupt %ebx when using INT 15,2401 (see
http://opensolaris.org/jive/thread.jspa?messageID=377026). Guard
against this by preserving all (non-segment) registers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The symbol_text16 is defined globally by the linker. Use rm_text16
instead of _text16 for the local variable within librm.S to avoid
confusion when reading linker maps.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
All users of imgdownload() require registration of the image, so make
registration an integral part of imgdownload() itself and simplify the
"action" parameter to be one of image_select(), image_exec() et al.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "sleep" command is generally useful to have. For example:
:dhcp_retry
dhcp && goto dhcp_done
sleep 5
goto dhcp_retry
:dhcp_done
Make the "sleep" command available by default, leaving TIME_CMD
controlling only the (fairly specialist) "time" command.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Arbel seems to crash the system as soon as the first send WQE
completes on an RC queue pair. (NOPs complete successfully, so this
is a problem specific to the work queue rather than the completion
queue.) The cause of this problem has remained unknown for over a
year.
Check in the non-functioning code to avoid bit-rot, and in the hope
that someone will find the fix.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This self-test mechanism is inspired by Perl's Test::Simple and
similar modules. The aim is to encourage the use of self-tests by
making it as easy as possible to create self-test code
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently uses the last four bytes of the MAC address as the DHCP
transaction identifier. Reduce the probability of collisions by
generating a random transaction identifier.
Originally-implemented-by: Amos Kong <akong@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a utility to quickly determine the ROM size and .mrom format
support for attached PCI devices. For example:
01:00.0 (1186:4300) supports a 128kB .rom or .mrom
Inspired-by: Wes Frazier <wes.frazier@members.fsf.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
TCP currently neglects to allow sufficient space for its own headers
when allocating I/O buffers. This problem is masked by the fact that
the maximum link-layer header size (802.11) is substantially larger
than the common Ethernet link-layer header.
Fix by allowing sufficient space for any TCP headers, as well as the
network-layer and link-layer headers.
Reported-by: Scott K Logan <logans@cottsay.net>
Debugged-by: Scott K Logan <logans@cottsay.net>
Tested-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The version field of an X.509 certificate appears to be optional.
Reported-by: Sebastiano Manusia <Sebastiano.Manusia@chuv.ch>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
CRLF line terminators are allowed in scripts; the carriage return is
simply interpreted as trailing whitespace and so is ignored. This
fails on lines containing script labels, since the label-finding code
checks for a line containing only the ":" marker and the label itself
(without any trailing whitespace).
Fix by allowing a label to be terminated by either a NUL or a
whitespace character.
Reported-by: Bovey Christian <Christian.Bovey@chuv.ch>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE specifies a value of 0 for cmdline_size, causing GRUB to not pass
in a command line. Fix by setting cmdline_size to the maximum value
of 2047.
Signed-off-by: Valentine Barshak <gvaxon@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
timer->refcnt is allowed to be NULL, in which case the timer's
expired() method may end up freeing the timer object.
Discovered using valgrind.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When transmitting, use the broadcast link-layer address for any
broadcast address (e.g. 192.168.0.255), not just INADDR_BROADCAST
(255.255.255.255).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Explicitly discard any unicast packets for addresses that we do not
control, to avoid unexpected behaviour when operating in promiscuous
mode (which is now the default, thanks to FCoE).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to section 14.23 of RFC2616, an HTTP Host header without
port implies the default port is used. Thus, when fetching from
anywhere but port 80 for HTTP or 443 for HTTPS, the port ought to be
explicitly given in that header. Otherwise, some servers might fail
to associate the request with the correct virtual host or generate
incorrect self-referencing URLs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reported-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iSCSI TX process can now be woken up by the TCP socket via
xfer_window_changed(), so it is no longer valid to assume that
iscsi_tx_step() can be called in state ISCSI_TX_IDLE only immediately
after completing a transmission.
Fix by calling iscsi_tx_done() only upon a transition into state
ISCSI_TX_IDLE.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some older versions of gcc issue a warning if -ffunction-sections is
used in combination with -g (gcc bug #18553). Inhibit
-ffunction-sections when building with such a version of gcc.
Reported-by: zhengwei <zw111_2001@126.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide support for HTTP range requests, and expose this functionality
via the iPXE block device API. This allows SAN booting from a root
path such as:
sanboot http://boot.ipxe.org/freedos/fdfullcd.iso
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow objects to support both streaming and block device protocols, by
starting streaming data only when the data transfer window opens.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Polling for the data-transfer window to become open is wasteful. We
can eliminate the polling loop by using hw_step() as the handler for
an xfer_window_changed() event.
If the window is already open at the time of instantiation, then
xfer_window_changed() may never be called. We can cover this case by
using hw_step() as the step() method of a one-shot process. Since the
signature for an xfer_window_changed() method is identical to the
signature for a process step() method, the same function can be used
for both.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some processes execute only once, and exist solely in order to defer
execution until after the relevant instantiator method has returned.
Such processes do not need to be automatically rescheduled when
executing.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give the step() method a pointer to the containing object, rather than
a pointer to the process. This is consistent with the operation of
interface methods, and allows a single function to serve as both an
interface method and a process step() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Modify the default action for xfer_vredirect() to automatically send
xfer_window_changed() messages to both the new child and the parent
interfaces. This will allow the elimination of processes that simply
poll on xfer_window() to determine when a redirection has completed
successfully.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ftp_data_deliver() does nothing except pass through the received data
to the xfer interface, and so can be eliminated by using a
pass-through interface.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some bootloaders seem to add "BOOT_IMAGE=..." at the end of the
command line; some at the start. Cope with either variation.
Reported-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At the time of attempting ARP resolution, we already know the
transmitting network device. We can therefore record ARP errors using
netdev_tx_err() so that they show up in the output of "ifstat".
Inspired-by: Dominik Russenberger <dominik.russenberger@terreactive.ch>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow TX errors to be recorded against a network device even when the
packet didn't make it as far as netdev_tx().
Inspired-by: Dominik Russenberger <dominik.russenberger@terreactive.ch>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
IBM BIOSes ignore the PnP header offset stored at address 0x1a and
instead scan for the $PnP signature on a 16-byte boundary. (This
alignment is not mandated by the PnP specification.)
Force PnP header to a 16-byte boundary to work around these BIOSes.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Several BIOSes (including most IBM BIOSes and many virtual machine
BIOSes) do not provide detectable PnP support, but will use the BEV
entry point for a PnP option ROM. On these semi-PnP BIOSes, iPXE will
respond to the absence of detectable PnP support by hooking INT19,
which disrupts the boot order.
BIOSes that genuinely require hooking INT19 seem to be very rare
nowadays. It may therefore be preferable to assume that the absence
of detectable PnP support indicates a semi-PnP BIOS rather than a
non-PnP BIOS.
Change the default behaviour so that INT19 will never be hooked unless
the compile-time option NONPNP_HOOK_INT19 is enabled. Leave the
redundant PnP detection routine in-place to allow for debugging via
the ROM banner line.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Revert commit 38cd351 ("[romprefix] Attempt to gracefully handle
semi-PnP IBM BIOSes"), since the test for the "IBM " signature in %edi
is not sufficient to identify an IBM BIOS.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
(Ab)use the "ident" field in transmitted IPv4 packets to convey
metadata about the network device. In particular:
bits 0-3 represent the low bits of the "RX" good packet counter
bits 4-7 represent the low bits of the "RXE" bad packet counter
bits 8-15 represent the transmitted packet sequence number
This allows some relevant information about the internal state of the
network device to be read out from a packet trace from a non-debug
build of iPXE. In particular, it allows a packet trace containing
packets transmitted by iPXE to indicate whether or not any packets
have been received by iPXE.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Booting from an HTTP SAN will require HTTP range requests, which are
defined only in HTTP/1.1 and above. HTTP/1.1 mandates support for
"Transfer-Encoding: chunked", so we must support it.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This reverts commit 15c1200 ("[hermon] Work around missing mport
support in current BOFM implementations").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Newer BOFM builds provide support for mapping multiple physical ports
to a single PCI bus:dev.fn via PCI VPD descriptions. These builds
will also leave the {slot,port} field intact, and will populate the
mport field with a meaningful value.
Older BOFM builds will zero out the {slot,port} field. A zero value
in this field may indicate either a genuine zero value (i.e. slot 0
first port) or an older build.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some IBM BIOSes provide partial support for PnP: they will use the BEV
entry point but will not advertise PnP support. This causes iPXE to
hook INT 19, which disrupts the boot process.
Attempt to improve this situation by detecting an IBM BIOS and
treating it as a PnP BIOS despite the absence of a PnP signature.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some versions of binutils have curious concepts of what constitutes
subtraction. For example:
0x00000000000000f0 _text16_late = .
0x0000000000000898 _mtext16 = .
0x0000000000000898 _etext16 = .
0x0000000000000898 _text16_late_filesz = ABSOLUTE ((_mtext16 - _text16_late))
0x00000000000007a8 _text16_late_memsz = ABSOLUTE ((_etext16 - _text16_late))
This has interesting side-effects such as producing sizes for .bss
segments that are negative, causing the majority of addressable memory
to be zeroed out.
Fix by using the form
ABSOLUTE ( x ) - ABSOLUTE ( y )
rather than
ABSOLUTE ( x - y )
Reported-by: H. Peter Anvin <hpa@zytor.com>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This allows older versions of ELTORITO.SYS (such as the version found
on the FreeDOS installation CD-ROM) to use iPXE's emulated CD-ROM
drive.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Make the build command line less cumbersome by accepting
make DEBUG=int13 EMBED=test.ipxe
rather then
make DEBUG=int13 EMBEDDED_IMAGE=test.ipxe
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose the multiple-SAN-drive capability of the iPXE core via the iPXE
command line by adding commands to hook and unhook additional drives.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some PXE stacks (notably old Etherboot/gPXE stacks) will claim to use
the timer interrupt, rather than reporting that interrupts are not
supported. Since using the timer interrupt is equivalent to polling
anyway, we may as well genuinely poll these stacks.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
PCI_ROM() and ISA_ROM() macros occur only within driver files.
Running parserom.pl on non-driver files is therefore redundant.
Skip running parserom.pl on any files outside a "drivers" directory.
This reduces the time taken to generate build rules and dependencies
after a "make veryclean" by around 12%.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There is no plausible scenario I can think of in which "isset" would
be used with more than one argument. Simplify the code by specifying
that exactly one argument is required.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Current BOFM versions are unable to create entries with mport>1, which
means that only the port 1 MAC address can be explicitly specified.
Work around this by using the provided MAC address as a base address
for all subsequent ports. For example, if BOFM assigns the address
00:1A:64:76:00:09 for port 1
then we will assign the addresses
00:1A:64:76:00:09 for port 1
00:1A:64:76:00:0a for port 2
Future BOFM versions that may correctly support mport will work with
this scheme without modification provided that the BOFM entries are
created in increasing order of mport. Since BOFM tools tend to
generate entries in increasing order (of slot, port, etc), this is not
an unreasonable compromise.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
GNU gold (part of newer binutils builds) does not appear to be
designed to support generic linker functionality, since its source
code contains several Linux-specific hard-coded assumptions about the
layout of ELF binaries. Attempting to build iPXE using GNU gold will
generally cause some kind of "linker internal error".
Provide an explicit error message suggesting the use of GNU ld
instead.
Reported-by: Chris Hills <chaz@chaz6.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 3f442d3 ("[tcp] Record ts_recent on first received packet")
failed to achieve its stated intention.
Fix this (and reduce the code size) by moving the ts_recent update to
tcp_rx_seq(). This is the code responsible for advancing the window,
called by both tcp_rx_syn() and tcp_rx_data(), and so the window check
is now redundant.
Reported-by: Frank Weed <zorbustheknight@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit b5f5f73 ("[cmdline] Expand settings within each command-line
token individually") introduced a regression into the "isset" command:
it is now possible for command-line arguments to be empty strings, and
so "isset" cannot simply check for a non-empty argument list.
Restore previous behaviour by checking for the presence of any
non-empty arguments, rather than checking for a non-empty argument
list.
Reported-by: Nemtallah Daher <n.daher@csuohio.edu>
Tested-by: Nemtallah Daher <n.daher@csuohio.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Set the current working URI to NULL rather than to "tftp://0.0.0.0/".
Reported-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Standardise on using init_editstring() to initialise an embedded
editable string, to match the coding style used by other embedded
objects.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A PCI_ROM() entry containing a vendor or device ID of PCI_ANY_ID
(0xffff) indicates to pci_find_driver() that the entry's vendor or
device ID should be ignored when matching against the device's vendor
or device ID. It does not represent a PCI ROM that should be built.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Each PCI ROM currently ends up appearing twice in the $(ROMS) list:
once under its designated name (e.g. "rtl8139.rom"), once under its
PCI IDs (e.g. "bin/10ec8139.rom").
Include only the latter of these in the $(ROMS) list, so that doing
"make allroms" will generate only one copy of each ROM.
Reported-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For devices that start in a link-down state, the user will see a
message such as:
[Link status: The socket is not connected (http://ipxe.org/38086001)]
Waiting for link-up on net0...
This is potentially misleading, since it suggests that there is a
genuine problem. Add a dedicated error message for "link down",
giving instead:
[Link status: Down (http://ipxe.org/38086101)]
Waiting for link-up on net0...
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The original EFI BOFM protocol has a design flaw that limits the size
of the table to 1kB, since the table is embedded within the
IBM_BOFM_DRIVER_CONFIGURATION_PROTOCOL structure. Version 2 of the
protocol works around this problem.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE operates the forcedeth NIC in promiscuous mode, and never changes
the unicast MAC address filter registers. We should not therefore set
the flag indicating (to other drivers loaded later) that the MAC
address order has already been corrected.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The forcedeth driver currently implements unicast MAC address
filtering in software. This is almost invariably the wrong thing to
do (since the network stack must already be able to cope with unwanted
packets) and it breaks FCoE (which requires the card to operate in
promiscuous mode).
Also, the implementation is buggy: is_local_ether_addr() is used to
check for a locally-assigned Ethernet address (not to check for a
unicast address), and the current link-layer address is in
netdev->ll_addr, not netdev->hw_addr.
Fix by removing this code.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A scriptlet is a single iPXE command that can be stored in
non-volatile option storage and used to override the default
"autoboot" behaviour without having to reflash the iPXE image.
For example, a scriptlet could contain
autoboot || reboot
to instruct iPXE to reboot the system if booting fails.
Unlike an embedded image, the presence of a scriptlet does not inhibit
the initial "Press Ctrl-B..." prompt. This allows the user to recover
from setting a faulty scriptlet.
Originally-implemented-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Perform settings expansion after tokenisation, and only at the point
of executing each command. This allows statements such as
dhcp && echo ${net0/ip}
to work correctly.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
It is currently possible to construct a sequence of commands to be
executed regardless of success or failure using "|| &&" as the command
separator. (The "||" captures the failure case, the blank command
converts it to a success case.)
Allow ";" to be used as a more visually appealing (and
space-efficient) alternative.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Temporary modification to prevent valgrind.h from breaking compilation
with gcc 4.6. When this problem is fixed upstream, a new and
unmodified copy of valgrind.h should be imported.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid unused-but-set variable warning in gcc 4.6 which was introduced
by commit 9215b7f ("[forcedeth] Clear the MII link status register on
link status changes").
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown