There are several points in the iPXE codebase where
list_for_each_entry() is (ab)used to extract only the first entry from
a list. Add a macro list_first_entry() to make this code easier to
read.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For some install-to-SAN scenarios, the OS needs to be able to reboot
to reread the partition table. On this second boot attempt, the SAN
disk will not be empty and so iPXE will attempt to boot from it,
rather than falling back to the OS' installation media.
Work around this problem by introducing the "skip-san-boot" option,
similar in spirit to "keep-san".
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some SCSI targets (observed with an EMC CLARiiON Fibre Channel target)
will not respond to commands correctly until a TEST UNIT READY has
been issued. In particular, a READ CAPACITY (10) command will return
with a success status, but no capacity data.
Fix by issuing a TEST UNIT READY command automatically, and delaying
further SCSI commands until the TEST UNIT READY has succeeded.
Reported-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 5f4ab0d ("[iscsi] Randomise a portion of the ISID to force new
session instantiation") introduced a regression by randomising the
ISID on each call to iscsi_start_login(), which may be called more
than once per connection, rather than on each call to
iscsi_open_connection(), which is guaranteed to be called only once
per connection. This is incorrect behaviour that causes our
connection to be rejected by some iSCSI targets (observed with a
COMSTAR target under OpenSolaris).
Fix by generating the ISID in iscsi_open_connection(), and storing the
randomised ISID as part of the session state.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
FCoE requires the use of fabric-provided MAC addresses, which breaks
the assumption that the net device's MAC address is implicitly the
source address for net_tx() and the (unicast) destination address for
net_rx().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Error numbers are signed ints. EUNIQ() should not allow implicit type
promotion based on the supplied error diambiguator, because this
causes problems with statements such as
rc = ( condition ? -EUNIQ ( EBASE, disambiguator ) : -EBASE );
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support the extensions mandated by EDD 4.0, including:
o the ability to specify a flat physical address in a disk address
packet,
o the ability to specify a sector count greater than 127 in a disk
address packet,
o support for all functions within the Fixed Disk Access and EDD
Support subsets,
o the ability to describe a device using EDD Device Path Information.
This implementation is based on draft revision 3 of the EDD 4.0
specification, with reference to the EDD 3.0 specification. It is
possible that this implementation may need to change in order to
conform to the final published EDD 4.0 specification.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The response to a received FLOGI should probably be sent to the peer
port ID assigned as a result of the WWPN comparison.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently uses the first port's port GUID as the node GUID,
rather than using the (possibly distinct) real node GUID. This can
confuse opensm during the handover to a loaded OS: it thinks the port
already belongs to a different node and so discards our port
information with a warning message about duplicate ports. Everything
is picked up correctly on the second subnet sweep, after opensm has
established that the "old" node no longer exists, but this can delay
link-up unnecessarily by several seconds.
Fix by using the real node GUID.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ib_smc_update() potentially updates the Infiniband port state, and so
should almost always be followed by a call to ib_link_state_changed().
The one exception is the call made to ib_smc_update() before the
device is registered.
Fix by removing explicit calls to ib_link_state_changed() from drivers
using ib_smc_update(), including a call to ib_link_state_changed()
within ib_smc_update(), and creating a separate ib_smc_init() for use
prior to device registration.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The sense key gives a first idea of what the problem might be, and so
is potentially useful in diagnosing problems in a non-debug build.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Fibre Channel Protocol provides a mechanism for transporting SCSI
commands via a Fibre Channel fabric.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for Fibre Channel ports, peers, and upper-layer protocols,
and for Fibre Channel extended link services.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The block device interface used in gPXE predates the invention of even
the old gPXE data-transfer interface, let alone the current iPXE
generic asynchronous interface mechanism. Bring this old code up to
date, with the following benefits:
o Block device commands can be cancelled by the requestor. The INT 13
layer uses this to provide a global timeout on all INT 13 calls,
with the result that an unexpected passive failure mode (such as
an iSCSI target ACKing the request but never sending a response)
will lead to a timeout that gets reported back to the INT 13 user,
rather than simply freezing the system.
o INT 13,00 (reset drive) is now able to reset the underlying block
device. INT 13 users, such as DOS, that use INT 13,00 as a method
for error recovery now have a chance of recovering.
o All block device commands are tagged, with a numerical tag that
will show up in debugging output and in packet captures; this will
allow easier interpretation of bug reports that include both
sources of information.
o The extremely ugly hacks used to generate the boot firmware tables
have been eradicated and replaced with a generic acpi_describe()
method (exploiting the ability of iPXE interfaces to pass through
methods to an underlying interface). The ACPI tables are now
built in a shared data block within .bss16, rather than each
requiring dedicated space in .data16.
o The architecture-independent concept of a SAN device has been
exposed to the iPXE core through the sanboot API, which provides
calls to hook, unhook, boot, and describe SAN devices. This
allows for much more flexible usage patterns (such as hooking an
empty SAN device and then running an OS installer via TFTP).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
DBG_ENABLE() and DBG_DISABLE() are currently constrained to enabling
and disabling only debug levels that are compiled in for the current
object. For example, a DBG_ENABLE(DBGLVL_EXTRA) in foo.c will not be
able to affect output from other objects at DBGLVL_EXTRA unless foo.c
is itself compiled with DBGLVL_EXTRA enabled.
Partially fix by removing this unnecessary constraint. (Note that it
is still necessary for at least one debug level to be compiled in for
the object invoking DBG_ENABLE()/DBG_DISABLE().)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
xfer_window_changed() can be used to notify peers that an interface is
now ready to accept data. This can potentially be used to eliminate
the need for wasteful processes that simply poll xfer_window() until
the window becomes non-zero.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the explicit calls from the Infiniband core to the IPoIB layer
with the general concept of an Infiniband upper-layer driver
(analogous to a PCI driver) which can create arbitrary devices on top
of Infiniband devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the concept of a network upper-layer driver, which can create
arbitrary devices on top of network devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Guarantee that a retry timer cannot go out of scope while the timer is
running, and provide a guarantee to the expiry callback that the timer
will remain in scope during the entire callback (similar to the
guarantee provided to interface methods).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE has never supported SEEK_END; the usage of "whence" offers only
the options of SEEK_SET and SEEK_CUR and so is effectively a boolean
flag. Further flags will be required to support additional metadata
required by the Fibre Channel network model, so repurpose the "whence"
field as a generic "flags" field.
xfer_seek() has always been used with SEEK_SET, so remove the "whence"
field altogether from its argument list.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Declarations without the accompanying __table_entry cause misalignment
of the table entries when using gcc 4.5. Fix by adding the
appropriate __table_entry macro or (where possible) by removing
unnecessary forward declarations.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Even with the noinline specifier added by commit 1a260f8, gcc may skip
calls to non-inlinable functions that it knows have no side
effects. This caused the get_cached_dhcpack() call in start_dhcp(),
the weak stub of which has no code in its body, to be removed,
preventing cached DHCP from working.
Fix by adding a __keepme macro to compiler.h expanding to asm(""), as
recommended by gcc's info page, and using it in the weak stub for
get_cached_dhcpack().
Reported-by: Aaron Brooks <aaron@brooks1.net>
Tested-by: Aaron Brooks <aaron@brooks1.net>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the tap driver that can be used like:
$ ./ipxe.linux --net tap,if=tap0,mac=00:0c:29:c5:39:a1
The if setting is mandatory.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support qemu-like arguments for network setup:
--net driver_name[,setting=value]*
and global settings:
--settings setting=value[,setting=value]*
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the base to build linux drivers and the linux UI code on. UI
fills device requests, which are later walked over by the linux
root_driver and delegated to specific linux drivers.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There exists an smbios userspace library so implementing this is
probably possible, but doesn't seem really important to have in
userspace. Hence provide a dummy implementation returning an error.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add user access API for linux.
On linux userspace virtual == user == phys addresses. Physical
addresses also being the same is wrong, but there is no general way of
converting userspace addresses to physical as what appears to be
contiguous in userspace is physically fragmented. Currently only the
DMA memory is special-cased, but its conversion to bus addresses is
done in phys_to_bus. This is known to break virtio as it is passing
phys addresses to the virtual device.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Don't implement strtoul() on top of strtoull() as strtoull() is much
bigger and only used on linux currently. Instead refactor most of the
logic out of strtoul() into static inlines and reuse that. Also put it
in a separate object so it won't get linked in.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
pcbios specific get_memmap() is used by the b44 driver making
all-drivers builds fail on other platforms. Move it to the I/O API
group and provide a dummy implementation on EFI.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow packets in the receive queue to be discarded in order to free up
memory. This avoids a potential deadlock condition in which the
missing packet can never be received because the receive queue is
occupying all of the memory available for further RX buffers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a facility allowing cached data to be discarded in order to
satisfy memory allocations that would otherwise fail.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Maintain a queue of received packets, so that lost packets need not
result in retransmission of the entire TCP window.
Increase the TCP window to 8kB, in order that we can potentially
transmit enough duplicate ACKs to trigger Fast Retransmission at the
sender.
Using a 10MB HTTP download in qemu-kvm with an artificial drop rate of
1 in 64 packets, this reduces the download time from around 26s to
around 4s.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch adds a native iPXE virtio-net driver and removes the legacy
Etherboot virtio-net driver. The main reasons for doing this are:
1. Multiple virtio-net NICs are now supported by iPXE. The legacy
driver kept global state and caused issues in virtual machines with
more than one virtio-net device.
2. Faster downloads. The native iPXE driver downloads 100 MB over
HTTP in 12s, the legacy Etherboot driver in 37s. This simple
benchmark uses KVM with tap networking and the Python
SimpleHTTPServer both running on the same host.
Changes to core virtio code reduce vring descriptors to 256 (QEMU uses
128 for virtio-blk and 256 for virtio-net) and change the opaque token
from u16 to void*. Lowering the descriptor count reduces memory
consumption. The void* opaque token change makes driver code simpler.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Weak functions whose visibility is hidden may be inlined due to a bug
in GCC. Explicitly mark weak functions noinline to work around the
problem.
This makes the PXE_MENU config option work again, the PXE boot menu
was never being called because the compiler inlined a weak stub
function.
The GCC bug was identified and fixed by Richard Sandiford
<rdsandiford@googlemail.com> but in the meantime iPXE needs to
implement a workaround.
Reported-by: Steve Jones <steve@squaregoldfish.co.uk>
Reported-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Suggested-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Continue calling step() while displaying the shell banner. This
potentially allows TCP connections to close gracefully after a failed
boot attempt.
Inspired-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Include the pause() and more() debugging functions within the general
iPXE debugging framework, by introducing DBGxxx_PAUSE() and
DBGxxx_MORE() macros.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
putline() was introduced back in 2007 for a feature that was never
committed. No console driver implements it and no code calls it, so
remove it from struct console_driver.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a PCI_CAP_ID_VNDR definition for the PCI standard "Vendor
Specific" capability ID.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since more reference-counted structures than embedded images might
want to mark themselves unfreeable, expose a dummy ref_no_free().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
xfer_vredirect() should not be allowed to propagate to a pass-through
interface. For example, when an HTTPS connection is opened, the
redirect message should cause the TLS layer to reopen the TCP socket,
rather than causing the HTTP layer to disconnect from the TLS layer.
Fix by allowing for non-pass-through interface methods, and setting
xfer_vredirect() to be one such method.
This is slightly ugly, in that it complicates the notion of an
interface method call by adding a "pass-through" / "non-pass-through"
piece of metadata. However, the only current user of xfer_vredirect()
is iscsi.c, which uses it only because we don't yet have an
ioctl()-style call for retrieving the underlying socket address.
The new interface infrastructure allows for such a call to be created,
at which time this sole user of xfer_vredirect() can be removed,
xfer_vredirect() can cease to be an interface method and become simply
a wrapper around xfer_vreopen(), and the concept of a non-pass-through
interface method can be reverted.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove data-xfer as an interface type, and replace data-xfer
interfaces with generic interfaces supporting the data-xfer methods.
Filter interfaces (as used by the TLS layer) are handled using the
generic pass-through interface capability. A side-effect of this is
that deliver_raw() no longer exists as a data-xfer method. (In
practice this doesn't lose any efficiency, since there are no
instances within the current codebase where xfer_deliver_raw() is used
to pass data to an interface supporting the deliver_raw() method.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove name-resolution as an interface type, and replace
name-resolution interfaces with generic interfaces supporting the
resolv_done() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove job-control as an interface type, and replace job-control
interfaces with generic interfaces supporting the close() method.
(Both done() and kill() are absorbed into the function of close();
kill() is merely close(-ECANCELED).)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We have several types of object interface at present (data-xfer, job
control, name resolution), and there is some duplication of
functionality between them. For example, job_done(), job_kill() and
xfer_close() are almost isomorphic to each other.
This updated version of the object interface mechanism allows for each
interface to export an arbitrary list of supported operations.
Advantages include:
Operations methods now receive a pointer to the object, rather than
a pointer to the interface. This allows an object to, for example,
implement a single close() method that can handle close() operations
from any of its exposed interfaces.
The close() operation is implemented as a generic operation (rather
than having specific variants for data-xfer, job control, etc.).
This will allow functions such as monojob_wait() to be used to wait
for e.g. a name resolution to complete.
The amount of boilerplate code required in objects is reduced, not
least because it is no longer necessary to include per-interface
methods that simply use container_of() to derive a pointer to the
object and then tail-call to a common per-object method.
The cost of adding new operations is reduced; adding a new data-xfer
operation such as stat() no longer incurs the penalty of adding a
.stat member to the operations table of all existing data-xfer
interfaces.
The data-xfer, job control and name resolution interfaces have not yet
been updated to use the new interface mechanism, but the code will
still compile and run.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Standardise on using timer_init() to initialise an embedded retry
timer, to match the coding style used by other embedded objects.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Standardise on using ref_init() to initialise an embedded reference
count, to match the coding style used by other embedded objects.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A new driver for JMicron Ethernet controller.
Reviewed-by: Joshua Oreman <oremanj@rwcr.net>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Reviewed-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a new network driver that consumes the EFI Simple Network
Protocol. Also add a bus driver that can find the Simple Network
Protocol that iPXE was loaded from; the resulting behavior is similar
to the "undionly" driver for BIOS systems.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Autodetect the BSD licence statement in EFI header files, and add a
suitable FILE_LICENCE macro to the version imported into the iPXE
tree.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Now that the PACKED macro conflict is resolved, we can use an
unmodified import of the EFI header files (using
include/ipxe/efi/import.pl).
Synchronised to EDK2 SVN revision 10556.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most of iPXE uses __attribute__((packed)) anyway, and PACKED conflicts
with an identically-named macro in the upstream EFI header files.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This removes the need for inline safety wrappers, marginally reducing
the size penalty of weak functions, and works around an apparent
binutils bug that causes undefined weak symbols to not actually be
NULL when compiling with -fPIE (as EFI builds do).
A bug in versions of binutils prior to 2.16 (released in 2005) will
cause same-file weak definitions to not work with those
toolchains. Update the README to reflect our new dependency on
binutils >= 2.16.
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some switch configurations will refuse to enable our port unless we
can speak LACP to inform the switch that we are alive. Add a very
simple passive LACP implementation that is sufficient to convince at
least Linux's bonding driver (when tested using qemu attached to a tap
device enslaved to a bond device configured as "mode=802.3ad").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This commit adds an igb (Intel GigaBit) driver based on Intel source
code available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support some PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit adds an e1000e driver based on Intel source code
available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support many PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit replaces the current gPXE e1000 driver with one ported
from Intel source code available at
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support most if not all PCI e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
The NMB protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The IGMP code came from legacy Etherboot and was never updated to work
as a gPXE protocol. There has been no demand for this protocol, so this
patch removes it.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The NFS protocol code came from legacy Etherboot and was never updated
to work as a gPXE protocol. There has been no demand for this protocol,
so this patch removes it.
I have an unfinished NFSv3 over TCP implementation for gPXE that can be
used as the base for new work, should we want to resurrect this
protocol.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Currently, handling of URI escapes is ad-hoc; escaped strings are
stored as-is in the URI structure, and it is up to the individual
protocol to unescape as necessary. This is error-prone and expensive
in terms of code size. Modify this behavior by unescaping in
parse_uri() and escaping in unparse_uri() those fields that typically
handle URI escapes (hostname, user, password, path, query, fragment),
and allowing unparse_uri() to accept a subset of fields to print so
it can be easily used to generate e.g. the escaped HTTP path?query
request.
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
For extremely tight space requirements and specific applications, it is
sometimes desirable to create gPXE images that cannot provide the PXE API
functionality to client programs. Add a configuration header option,
PXE_STACK, that can be removed to remove this stack. Also add PXE_MENU
to control the PXE boot menu, which most uses of gPXE do not need.
Signed-off-by: Marty Connor <mdc@etherboot.org>
When a DHCP session is started (using autoboot or a command-line `dhcp
net0'), check whether the new setting use-cached (DHCP option 175.178)
is TRUE; if so, skip DHCP and rely on currently registered
settings. This lets one combine a static IP with autoboot.
Before checking the use-cached setting, call a weak
get_cached_dhcpack() hook that can be implemented by particular builds
of gPXE supporting some fashion of retrieving a cached DHCPACK packet.
If one is available, it is registered as an options source, and then
either that packet's option 175.178 or the user's prior manual
use-cached setting can allow skipping duplicate DHCP.
Using cached packets is not the default because DHCP servers are often
configured to give gPXE different options than they give a vendor PXE
client; in order to break the infinite loop of PXE chaining, one would
need to load a gPXE with an embedded image that does something more
than autoboot.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Weak symbols are a useful tool in eliminating unnecessary dependencies
between object files, but they are somewhat dangerous because one must
remember to test the weak symbol against NULL before using it. To
rectify that, add macros for declaring weak functions that will return
a default value inline if the file defining them is not available at
link time.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This code is based on the linux skge driver. It supports Marvell Yukon
and SysKonnect Gigabit chipsets.
The code is based on code Michael Decker <mrd999@gmail.com> wrote for
Google Summer of Code 2008.
Support for dual-port cards is untested. The code, however, was left
in. In my opinion it's easier to fix the code if we need to, instead
of having to add support for it from scratch.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This driver supports all current Myricom 10 gigabit Ethernet NICs.
It was written from scratch for gPXE by Glenn Brown <glenn@myri.com>,
referenencing Myricom's Linux and EFI drivers, with permission.
Signed-off-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Taken from Linux /usr/include/linux/pci.h .
Signed-off-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
EAPOL is a container protocol that can wrap either EAP packets or
802.11 EAPOL-Key frames. For cleanliness' sake, add a stub that strips
the framing and sends packets off to the appropriate handler if it
is compiled in.
Signed-off-by: Marty Connor <mdc@etherboot.org>
WEP is a highly flawed cryptosystem, barely better than no encryption at all,
but many people still use it. It does have the advantage of being very simple
and small in code size.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Add commands `iwstat' (to list 802.11-specific status information for
802.11 devices) and `iwlist' (to scan for available networks and print
a list along with security information).
Signed-off-by: Marty Connor <mdc@etherboot.org>
This fixes an issue where passing a length as a compound expression
(e.g. using `hdrlen + datalen') would trigger compiler warnings and
potentially precedence-related errors.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Both of these routines are used by 802.11 WPA, but they are generic
and could be needed by other protocols as well.
Signed-off-by: Marty Connor <mdc@etherboot.org>
It is often the case that some module of gPXE is only relevant if the
subsystem it depends on is already being included. For instance,
commands to manage wireless interfaces are quite useless if no
compiled-in driver has pulled in the wireless networking stack. There
may be a user-modifiable configuration options for these dependent
modules, but even if enabled, they should not be included when they
would be useless.
Solve this by allowing the creation of config_subsystem.c, for
configuration directives like those in the global config.c that should
only be considered when subsystem.c is included in the final gPXE
build.
For consistency, move core/config.c to the config/ directory, where
the other config_subsystem.c files will eventually reside.
Signed-off-by: Marty Connor <mdc@etherboot.org>
REQUIRE_SYMBOL() formerly used a formulation of symbol requirement
that would allow a link to succeed despite lacking a required symbol,
because it did not introduce any relocations. Fix by renaming it to
REQUEST_SYMBOL() (since the soft-requirement behavior can be useful)
and add a REQUIRE_SYMBOL() that truly requires.
Add EXPORT_SYMBOL() and IMPORT_SYMBOL() for REQUEST_SYMBOL()-like
behavior that allows one to make use of the symbol, by combining a
weak external on the symbol itself with a REQUEST_SYMBOL() of a second
symbol.
Signed-off-by: Marty Connor <mdc@etherboot.org>
The first byte of the IPoIB MAC address is used for flags indicating
support for "connected mode". Strip out the non-QPN bits of the first
dword when constructing the address vector for transmitted IPoIB
packets, so as not to end up passing an invalid QPN in the BTH.
The iBFT is Ethernet-centric in providing only six bytes for a MAC
address. This is most probably an indirect consequence of a similar
design flaw in the Windows NDIS stack. (The WinOF IPoIB stack
performs all sorts of contortions in order to pretend to the NDIS
layer that it is dealing with six-byte MAC addresses.)
There is no sensible way in which to extend the iBFT without breaking
compatibility with programs that expect to parse it. Add the notion
of an "Ethernet-compatible" MAC address to our link layer abstraction,
so that link layers can provide their own workarounds for this
limitation.
Some devices can only be reset via a mechanism that also resets the
card's PCI core, thus necessitating a backup and restore of all or
part of the PCI configuration space across a reset.
802.11 multicast hashing is the same as standard Ethernet hashing, so
just expose and use eth_mc_hash().
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
For IPoIB, the chaddr field is too small (16 bytes) to contain the
20-byte IPoIB link-layer address. RFC4390 mandates that we should
pass an empty chaddr field and rely on the DHCP client identifier
instead. This has many problems, not least of which is that a client
identifier containing an IPoIB link-layer address is not very useful
from the point of view of creating DHCP reservations, since the QPN
component is assigned at runtime and may vary between boots.
Leave the DHCP client identifier as-is, to avoid breaking existing
setups as far as possible, but expose the real hardware address (the
port GUID) via the DHCP chaddr field, using the broadcast flag to
instruct the DHCP server not to use this chaddr value as a link-layer
address.
This makes it possible (at least with ISC dhcpd) to create DHCP
reservations using host declarations such as:
host duckling {
fixed-address 10.252.252.99;
hardware unknown-32 00:02:c9:02:00:25:a1:b5;
}
IPoIB has a 20-byte link-layer address, of which only eight bytes
represent anything relating to a "hardware address".
The PXE and EFI SNP APIs expect the permanent address to be the same
size as the link-layer address, so fill in the "permanent address"
field with the initial link layer address (as generated by
register_netdev() based upon the real hardware address).
The hardware address is an intrinsic property of the hardware, while
the link-layer address can be changed at runtime. This separation is
exposed via APIs such as PXE and EFI, but is currently elided by gPXE.
Expose the hardware and link-layer addresses as separate properties
within a net device. Drivers should now fill in hw_addr, which will
be used to initialise ll_addr at the time of calling
register_netdev().
There is diagnostic value in being able to disambiguate between the
various reasons why an IB CM has rejected a connection attempt. In
particular, reason 8 "invalid service ID" can be used to identify an
incorrect SRP service_id root-path component, and reason 28 "consumer
reject" corresponds to a genuine SRP login rejection IU, which can be
passed up to the SRP layer.
For rejection reasons other than "consumer reject", we should not pass
through the private data, since it is most likely generated by the CM
without any protocol-specific knowledge.
With iSCSI, connection attempts are expensive; it may take many
seconds to determine that a connection will fail. SRP connection
attempts are much less expensive, so we may as well avoid the
"optimisation" of declaring a state of permanent failure after a
certain number of attempts. This allows a gPXE SRP initiator to
resume operations after an arbitrary amount of SRP target downtime.
SRP is the SCSI RDMA Protocol. It allows for a method of SAN booting
whereby the target is responsible for reading and writing data using
Remote DMA directly to the initiator's memory. The software initiator
merely sends and receives SCSI commands; it never has to touch the
actual data.
The minimal-surprise behaviour, when no explicit SRP initiator device
is specified, will probably be to use the most recently opened
Infiniband device. This matches our behaviour with using the most
recently opened net device for PXE, iSCSI, AoE, NBI, etc.
SRP over Infiniband uses a protocol whereby data is sent via a
combination of the CM private data fields and the RC queue pair
itself. This seems sufficiently generic that it's worth having
available as a separate protocol.
We will terminate our transaction as soon as we receive the first CM
REP, since that provides all the state that we need. However, the
peer may resend the REP if it didn't see our RTU, and if we don't
respond with another RTU we risk being disconnected. (This protocol
appears not to handle retries gracefully.)
Fix by adding a management agent that will listen for these duplicate
REPs and send back an RTU.
Previously the maximum packet length was computed using an erroneous
understanding of the role of the MIC field in TKIP-encrypted packets.
The field is actually considered to be part of the MSDU (encrypted and
fragmented data), not the MPDU (container for each encrypted
fragment). As such its size does not contribute to cryptographic
overhead outside the data field's size limitations. The net result is
that the previous maximum packet length value was 4 bytes too long;
fix it to the correct value of 2352.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
The prior net80211 model of physical-layer behavior for drivers was
overly simplistic and limited the drivers that could be written. To
be more flexible, split the driver-provided list of supported rates by
band, and add a means for specifying a list of supported channels.
Allow drivers to specify a hardware channel value that will be tied to
uses of the channel.
Expose net80211_duration() to drivers, and make the rate it uses in
its computations configurable, so that it can be used in calculating
durations that must be set in hardware for ACK and CTS packets. Add
net80211_cts_duration() for the common case of calculating the
duration for a CTS packet.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
A management interface is the component through which both local and
remote management agents are accessed.
This new implementation of a management interface allows for the user
to react to timed-out transactions, and also allows for cancellation
of in-progress transactions.
The IBA specification refers to management "interfaces" and "agents".
The interface is the component that connects to the queue pair and
sends and receives MADs; the agent is the component that constructs
the reply to the MAD.
Rename the IB_{QPN,QKEY,QPT} constants as a first step towards making
this separation in gPXE.
This is required for all modern 802.11 devices, and allows drivers
to be written for them with minimally more effort than is required
for a wired NIC.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
Modified-by: Michael Brown <mcb30@etherboot.org>
Queue pairs are now assumed to be created in the INIT state, with a
call to ib_modify_qp() required to bring the queue pair to the RTS
state.
ib_modify_qp() no longer takes a modification list; callers should
modify the relevant queue pair parameters (e.g. qkey) directly and
then call ib_modify_qp() to synchronise the changes to the hardware.
The packet sequence number is now a property of the queue pair, rather
than of the device.
Each queue pair may have an associated address vector. For RC queue
pairs, this is the address vector that will be programmed in to the
hardware as the remote address. For UD queue pairs, it will be used
as the default address vector if none is supplied to ib_post_send().
Now that MAD handlers no longer return a status code, we can allow
them to return a pointer to a MAD structure if and only if they want
to send a response. This provides a more natural and flexible
approach than using a "response method" field within the handler's
descriptor.
MAD handlers have to set the status fields within the MAD itself
anyway, in order to provide a meaningful response MAD; the additional
gPXE return status code is just noise.
Note that we probably don't need to ever explicitly set the status to
IB_MGMT_STATUS_OK, since it should already have this value from the
request. (By not explicitly setting the status in this way, we can
safely have ib_sma_set_xxx() call ib_sma_get_xxx() in order to
generate the GetResponse MAD without worrying that ib_sma_get_xxx()
will clear any error status set by ib_sma_set_xxx().)
Most IB hardware seems not to allow allocation of the genuine QPNs 0
and 1, so allow for the externally-visible QPN (as constructed and
parsed by ib_packet, where used) to differ from the real
hardware-allocated QPN.
Generalise the subnet management agent into a general management agent
capable of sending and responding to MADs, including support for
retransmissions as necessary.
Currently, all Infiniband users must create a process for polling
their completion queues (or rely on a regular hook such as
netdev_poll() in ipoib.c).
Move instead to a model whereby the Infiniband core maintains a single
process calling ib_poll_eq(), and polling the event queue triggers
polls of the applicable completion queues. (At present, the
Infiniband core simply polls all of the device's completion queues.)
Polling a completion queue will now implicitly refill all attached
receive work queues; this is analogous to the way that netdev_poll()
implicitly refills the RX ring.
Infiniband users no longer need to create a process just to poll their
completion queues and refill their receive rings.
IPoIB and the SMA have separate constants for the packet size to be
used to I/O buffer allocations. Merge these into the single
IB_MAX_PAYLOAD_SIZE constant.
(Various other points in the Infiniband stack have hard-coded
assumptions of a 2048-byte payload; we don't currently support
variable MTUs.)
IPoIB has a link-layer broadcast address that varies according to the
partition key. We currently go through several contortions to pretend
that the link-layer address is a fixed constant; by making the
broadcast address a property of the network device rather than the
link-layer protocol it will be possible to simplify IPoIB's broadcast
handling.
Move the icky call to step() from aoe.c to ata.c; this takes it at
least one step further away from where it really doesn't belong.
Unfortunately, AoE has the ugly aoe_discover() mechanism which means
that we still have a step() loop in aoe.c for now; this needs to be
replaced at some future point.
The PXE debugging messages have remained pretty much unaltered since
Etherboot 5.4, and are now difficult to read in comparison to most of
the rest of gPXE.
Bring the pxe_undi debug messages up to normal gPXE standards.
Expand the NETDEV_LINK_UP bit into a link_rc status code field,
allowing specific reasons for link failure to be reported via
"ifstat".
Originally-authored-by: Joshua Oreman <oremanj@rwcr.net>
In order to construct outgoing link-layer frames or parse incoming
ones properly, some protocols (such as 802.11) need more state than is
available in the existing variables passed to the link-layer protocol
handlers. To remedy this, add struct net_device *netdev as the first
argument to each of these functions, so that more information can be
fetched from the link layer-private part of the network device.
Updated all three call sites (netdevice.c, efi_snp.c, pxe_undi.c) and
both implementations (ethernet.c, ipoib.c) of ll_protocol to use the
new argument.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
The 93C66 is identical to the 93C56 in programming interface and
addressing, but twice as large in data storage (4096 bits). It's
used in some RTL8185 wireless cards.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
gPXE responds to duplicated ACKs with an immediate retransmission,
which can lead to a sorceror's apprentice syndrome. It also responds
to out-of-range (or old duplicate) ACKs with a RST, which can cause
valid connections to be dropped.
Fix the sorceror's apprentice syndrome by leaving the retransmission
timer running (and so inhibiting the immediate retransmission) when we
receive a potential duplicate ACK. This seems to match the behaviour
of Linux observed via wireshark traces.
Fix the RST issue by sending RST only on out-of-range ACKs that occur
before the connection is fully established, as per RFC 793.
These problems were exposed during development of the 802.11 wireless
link layer; the 802.11 protocol has a failure mode that can easily
cause duplicated packets. The fixes were tested in a controlled way
by faking large numbers of duplicated packets in the rtl8139 driver.
Originally-fixed-by: Joshua Oreman <oremanj@rwcr.net>
MAX_LL_HEADER_LEN is erroneously set to 6 rather than 14, resulting
in possible data corruption whenever we send an ARP packet.
Fix value and add a comment explaining why MAX_LL_ADDR_LEN is greater
than MAX_LL_HEADER_LEN.
Reported-by: Joshua Oreman <oremanj@rwcr.net>
Windows text editors such as Notepad tend to use CRLF line endings,
which breaks gPXE's signature detection for script images. Since
scripts are usually very small, they end up falling back to being
detected as valid PXE executable images (since there are no signature
checks for PXE executables). Executing text files as x86 machine code
tends not to work well.
Fix by allowing for any isspace() character to terminate the "#!gpxe"
signature, and by ensuring that CR characters get stripped during
command line parsing.
Suggested-by: Shao Miller <Shao.Miller@yrdsb.edu.on.ca>
Several SPI chips will respond to an SPI read command with a dummy
zero bit immediately prior to the first real data bit. This can be
used to autodetect the address length, provided that the command
length and data length are already known, and that the MISO data line
is tied high.
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
For partly historical reasons, various files in the gPXE source tree
are licensed under different, though compatible, terms. Most of the
code is licensed under GPLv2 with the "or later" clause, but there are
exceptions such as:
The string.h file, which derives from Linux and is licensed as
Public Domain.
The EFI header files, which are taken from the EDK2 source tree and
are licensed under BSD.
The 3c90x driver, which has a custom GPL-like licence text.
Introduce a FILE_LICENCE() macro to make licensing more explicit.
This macro should be applied exactly once to each source (.c, .S or
.h) file. It will cause a corresponding zero-sized common symbol to
be added to any .o files generated from that source file (and hence to
any final gPXE binaries generated from that source file). Determining
the applicable licences to generated files can then be done using e.g.
$ objdump -t bin/process.o | grep __licence
00000000 O *COM* 00000001 .hidden __licence_gpl2_or_later
indicating that bin/process.o is covered entirely by the GPLv2
with the "or later" clause, or
$ objdump -t bin/rtl8139.dsk.tmp | grep __licence
00033e8c g O .bss.textdata 00000000 .hidden __licence_gpl2_only
00033e8c g O .bss.textdata 00000000 .hidden __licence_gpl2_or_later
00033e8c g O .bss.textdata 00000000 .hidden __licence_public_domain
indicating that bin/rtl8139.dsk includes both code licensed under
GPLv2 (both with and without the "or later" clause) and code licensed
as Public Domain.
Determining the result of licence combinations is currently left as an
exercise for the reader.
The Mac compiler treats "#pragma pack()" as gcc's "#pragma pack(pop)",
and so dies if the pragma pack stack is empty. Adding a "#pragma
pack(1)" immediately beforehand is enough to keep the Mac compiler
happy.
The combination of "#pragma pack(1)", "#pragma pack()" won't actually
achieve anything on a Mac, but it will at least build. (With gcc, the
"#pragma pack()" overrides any previous pragmas, so is still useful.)
Suggested-by: Joshua Oreman <oremanj@rwcr.net>
Eliminate the potential for mismatches between table names and the
table entry data type by incorporating the data type into the
definition of the table, rather than specifying it explicitly in each
table accessor method.
Intel's C compiler (icc) chokes on the zero-length arrays that we
currently use as part of the mechanism for accessing linker table
entries. Abstract away the zero-length arrays, to make a port to icc
easier.
Introduce macros such as for_each_table_entry() to simplify the common
case of iterating over all entries in a linker table.
Represent table names as #defined string constants rather than
unquoted literals; this avoids visual confusion between table names
and C variable or type names, and also allows us to force a
compilation error in the event of incorrect table names.
Allow for settings blocks to be created on demand. This allows for
constructions such as
set defaults/filename http://bootserver/bootfile
set defaults/priority 0xff
dhcp net0
chain ${filename}
which will boot from the DHCP-provided filename, or from
"http://bootserver/bootfile" if the DHCP server does not provide a
filename.
(Note that "priority" gets interpreted as a signed integer, so setting
"defaults/priority" to 0xff will cause the "defaults" settings block
to have an effective priority of -1.)
Having a default script containing
#!gpxe
autoboot
can cause problems when entering commands to load and start a kernel
manually; the default script image will still be present when the
kernel is started and so will be treated as an initrd. It is possible
to work around this by typing "imgfree" before any other commands, but
this is counter-intuitive.
Fix by allowing the embedded image list to be empty (in which case we
just call autoboot()), and making this the default.
Reported by alkisg@gmail.com.
Avoid passing credentials in the iBFT that were available but not
required for login. This works around a problem in the Microsoft
iSCSI initiator, which will refuse to initiate sessions if the CHAP
password is fewer than 12 characters, even if the target ends up not
asking for CHAP authentication.
It is a programming error, not a runtime error, if we attempt to use
block ciphers with an incorrect blocksize, so use an assert() rather
than an error status return.
The various types of cryptographic algorithm are fundamentally
different, and it was probably a mistake to try to handle them via a
single common type.
pubkey_algorithm is a placeholder type for now.
Certain combinations of PXE stack and BIOS result in a broken INT 18
call, which will leave the system displaying a "PRESS ANY KEY TO
REBOOT" message instead of proceeding to the next boot device. On
these systems, returning via the PXE stack is the only way to continue
to the next boot device. Returning via the PXE stack works only if we
haven't already blown away the PXE base code in pxeprefix.S.
In most circumstances, we do want to blow away the PXE base code.
Base memory is a limited resource, and it is desirable to reclaim as
much as possible. When we perform an iSCSI boot, we need to place the
iBFT above the 512kB mark, because otherwise it may not be detected by
the loaded OS; this may not be possible if the PXE base code is still
occupying that memory.
Introduce a new prefix type .kkpxe which will preserve both the PXE
base code and the UNDI driver (as compared to .kpxe, which preserves
the UNDI driver but uninstalls the PXE base code). This prefix type
can be used on systems that are known to experience the specific
problem of INT 18 being broken, or in builds (such as gpxelinux.0) for
which it is particularly important to know that returning to the BIOS
will work.
Written by H. Peter Anvin <hpa@zytor.com> and Stefan Hajnoczi
<stefanha@gmail.com>, minor structural alterations by Michael Brown
<mcb30@etherboot.org>.
Multi-level menus via COMBOOT rely on the COMBOOT program being able
to exit and invoke a new COMBOOT program (the next menu). This works,
but rapidly (within about five iterations) runs out of space in gPXE's
internal stack, since each new image is executed in a new function
context.
Fix by allowing tail recursion between images; an image can now
specify a replacement image for itself, and image_exec() will perform
the necessary tail recursion.
This patch extends the embedded image feature to allow multiple
embedded images instead of just one.
gPXE now always boots the first embedded image on startup instead of
doing the hardcoded DHCP boot (aka autoboot).
Based heavily upon a patch by Stefan Hajnoczi <stefanha@gmail.com>.
Various combinations of options 43.6, 43.7 and 43.8 dictate which
servers we send Boot Server Discovery requests to, and which servers
we should accept responses from. Obey these options, and remove the
explicit specification of a single Boot Server from start_pxebs() and
dependent functions.
There are many functions that take ownership of the I/O buffer they
are passed as a parameter. The caller should not retain a pointer to
the I/O buffer. Use iob_disown() to automatically nullify the
caller's pointer, e.g.:
xfer_deliver_iob ( xfer, iob_disown ( iobuf ) );
This will ensure that iobuf is set to NULL for any code after the call
to xfer_deliver_iob().
iob_disown() is currently used only in places where it simplifies the
code, by avoiding an extra line explicitly setting the I/O buffer
pointer to NULL. It should ideally be used with each call to any
function that takes ownership of an I/O buffer. (The SSA
optimisations will ensure that use of iob_disown() gets optimised away
in cases where the caller makes no further use of the I/O buffer
pointer anyway.)
If gcc ever introduces an __attribute__((free)), indicating that use
of a function argument after a function call should generate a
warning, then we should use this to identify all applicable function
call sites, and add iob_disown() as necessary.
The DHCP client code now implements only the mechanism of the DHCP and
PXE Boot Server protocols. Boot Server Discovery can be initiated
manually using the "pxebs" command. The menuing code is separated out
into a user-level function on a par with boot_root_path(), and is
entered in preference to a normal filename boot if the DHCP vendor
class is "PXEClient" and the PXE boot menu option exists.
Try to qualify relative names in the DNS resolver using the DHCP Domain
Name. For example:
DHCP Domain Name: etherboot.org
(Relative) Name: www
yields:
www.etherboot.org
Only names with no dots ('.') will be modified. A name with one or more
dots is unchanged.
PXE dictates a mechanism for boot menuing, involving prompting the
user with a variable message, waiting for a predefined keypress,
displaying a boot menu, and waiting for a selection.
This breaks the currently desirable abstraction that DHCP is a process
that can happen in the background without any user interaction.
F8 is represented by the ANSI escape sequence "^[[19~", which is not
representable as a KEY_xxx constant using the current encoding scheme.
Adapt the encoding scheme to allow F8 to be represented, since PXE
requires that we may need to prompt the user to press F8.
Remove the lazy assumption that ProxyDHCP == "DHCP with option 60 set
to PXEClient", and explicitly separate the notion of ProxyDHCP from
the notion of packets containing PXE options.
Pick out the first boot menu item from the boot menu (option 43.9) and
pass it to the boot server as the boot menu item (option 43.71).
Also improve DHCP debug messages to include more details of the
packets being transmitted.
Some PXE configurations require us to perform a third DHCP transaction
(in addition to the real DHCP transaction and the ProxyDHCP
transaction) in order to retrieve information from a "Boot Server".
This is an experimental implementation, since the actual behaviour is
not well specified in the PXE spec.
When sending to a multicast address, it may be necessary to specify
the source address explicitly, since the multicast destination address
does not provide enough information to deduce the source address via
the miniroute table.
Allow the source address specified via the data-xfer metadata to be
passed down through the TCP/IP stack to the IPv4 layer, which can use
it as a default source address.
Include a minimal component name protocol so that the driver name
shows up as something other than "<UNKNOWN>" in the driver list, and a
device path protocol so that the network interface shows up as a
separate device in the device list, rather than being attached
directly to the PCI device.
Incidentally, the EFI component name protocol reaches new depths for
signal-to-noise ratio in program code. A typical instance within the
EFI development kit will use an additional 300 lines of code to
provide slightly less functionality than GNU gettext achieves with
three additional characters.
elf2efi converts a suitable ELF executable (containing relocation
information, and with appropriate virtual addresses) into an EFI
executable. It is less tightly coupled with the gPXE build process
and, in particular, does not require the use of a hand-crafted PE
image header in efiprefix.S.
elf2efi correctly handles .bss sections, which significantly reduces
the size of the gPXE EFI executable.
Conventional usage of the various struct sockaddr_xxx types involves
liberal use of casting, which tends to trigger strict-aliasing
warnings from gcc. Avoid these now and in future by marking all the
relevant types with __attribute__((may_alias)).
Michael Brown