The PXE spec does not specify a byte ordering for UUIDs, but RFC4578
suggests that it follows the EFI spec, in which the first three fields
are little-endian.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE treats UUIDs as being in network byte order (big-endian). The
SMBIOS specification version 2.6 states that UUIDs are stored with
little-endian values in the first three fields; earlier versions did
not specify an endianness. This results in some inconsistency between
the BIOS, vendor PXE, iPXE, and operating system interpretations of
the SMBIOS UUID.
dmidecode assumes that the byte order is little-endian if and only if
the SMBIOS version is 2.6 or higher. Choose to match this behaviour.
Reported-by: Matthew Helton <mwhelton@gmail.com>
Reported-by: Alexandru Bordei <alexandru.bordei@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 2629b7e ("[pcbios] Inhibit all calls to INT 15,e820 and INT
15,e801 during POST") introduced a regression into .lkrn images when
used with no corresponding initrd.
Specifically, the semantics of the "maximum address for relocation"
value passed to install_prealloc() in %ebp changed so that zero became
a special value meaning "inhibit use of INT 15,e820 and INT 15,e801".
The %ebp value meaing "no upper limit on relocation" was changed from
zero to 0xffffffff, and all prefixes providing fixed values for %ebp
were updated to match the new semantics.
The .lkrn prefix provides the initrd base address as the maximum
address for relocation. When no initrd is present, this address will
be zero, and so will unintentionally trigger the "inhibit INT 15,e820
and INT 15,e801" behaviour.
Fix by explicitly setting %ebp to 0xffffffff if no initrd is present
before calling install_prealloc().
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Tested-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Newer versions of bfd.h require definitions for the PACKAGE and
PACKAGE_VERSION macros used by autotools. Work around this by
manually defining these macros before including bfd.h.
Originally-fixed-by: Brandon Penglase <bpenglase-ipxe@spaceservices.net>
Tested-by: Brandon Penglase <bpenglase-ipxe@spaceservices.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When iPXE is used as a UEFI driver, the UEFI PXE base code currently
provides the TCP/IP stack, network protocols, and user interface.
This represents a substantial downgrade from the standard BIOS iPXE
user experience.
Fix by installing our own EFI_LOAD_FILE_PROTOCOL implementation which
initiates the standard iPXE boot procedure. This upgrades the UEFI
iPXE user experience to match the standard BIOS iPXE user experience.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose iPXE's images as a UEFI file system, allowing the booted image
to access all images downloaded by iPXE.
This functionality is complementary to the custom iPXE download
protocol. The iPXE download protocol allows a booted image to utilise
iPXE to download arbitrary URIs, but requires the booted image to
specifically support the custom iPXE download protocol. The new
functionality limits the booted image to accessing only files that
were already downloaded by iPXE (e.g. as part of a script), but can
work with any generic UEFI image (e.g. the UEFI shell). Both
protocols are provided simultaneously, and are attached to the SNP
device handle.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If a multifunction PCI device exposes an iPXE ROM via each function,
then each function will display a "Press Ctrl-B to configure iPXE"
prompt, and delay for two seconds. Since a single instance of iPXE
can drive all functions on the multifunction device, this simply adds
unnecessary delay to the boot process.
Fix by inhibiting the "Press Ctrl-B" prompt for all except the first
function on a PCI device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Many BIOSes do not construct the full system memory map until after
calling the option ROM initialisation entry points. For several
years, we have added sanity checks and workarounds to accommodate
charming quirks such as BIOSes which report the entire 32-bit address
space (including all memory-mapped PCI BARs) as being usable RAM.
The IBM x3650 takes quirky behaviour to a new extreme. Calling either
INT 15,e820 or INT 15,e801 during POST doesn't just get you invalid
data. We could cope with invalid data. Instead, these nominally
read-only API calls manage to trash some internal BIOS state, with the
result that the system memory map is _never_ constructed. This tends
to confuse subsequent bootloaders and operating systems.
[ GRUB 0.97 fails in a particularly amusing way. Someone thought it
would be a good idea for memcpy() to check that the destination memory
region is a valid part of the system memory map; if not, then memcpy()
will sulk, fail, and return NULL. This breaks pretty much every use
of memcpy() including, for example, those inserted implicitly by gcc
to copy non-const initialisers. Debugging is _fun_ when a simple call
to printf() manages to create an infinite recursion, exhaust the
available stack space, and shut down the CPU. ]
Fix by completely inhibiting calls to INT 15,e820 and INT 15,e801
during POST.
We do now allow relocation during POST up to the maximum address
returned by INT 15,88 (which seems so far to always be safe). This
allows us to continue to have a reasonable size of external heap, even
if the PMM allocation is close to the 1MB mark.
The downside of allowing relocation during POST is that we may
overwrite PMM-allocated memory in use by other option ROMs. However,
the downside of inhibiting relocation, when combined with also
inhibiting calls to INT 15,e820 and INT 15,e801, would be that we
might have no external heap available: this would make booting an OS
impossible and could prevent some devices from even completing
initialisation.
On balance, the lesser evil is probably to allow relocation during
POST (up to the limit provided by INT 15,88). Entering iPXE during
POST is a rare operation; on the even rarer systems where doing so
happens to overwrite a PMM-allocated region, then there exists a
fairly simple workaround: if the user enters iPXE during POST and
wishes to exit iPXE, then the user must reboot. This is an acceptable
cost, given the rarity of the situation and the simplicity of the
workaround.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
romprefix.S currently calls uninstall() with an invalid value in %ax.
Consequently, base memory is not freed after a ROM boot attempt (or
after entering iPXE during POST).
The uninstall() function is physically present in .text16, and so can
use %cs to determine the .text16 segment address. The .data16 segment
address is not required, since uninstall() is called only by code
paths which set up .data16 to immediately follow .text16.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add "make vmware" build target, to build all of the ROMs used with
VMware.
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The PXE TFTP API allows the caller to request a particular TFTP block
size. Since mid-2008, iPXE has appended a "?blksize=xxx" parameter to
the TFTP URI constructed internally; nothing has ever parsed this
parameter. Nobody seems to have cared that this parameter has been
ignored for almost five years.
Fix by using xfer_window(), which provides a fairly natural way to
convey the block size information from the PXE TFTP API to the TFTP
protocol layer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Nothing currently prevents a menu separator from being assigned a
shortcut key, and then from being selected using that shortcut key.
This produces an inconsistency in the user interface, since separators
cannot be selected by other means of menu navigation (arrow keys, page
up/down, etc).
It would be trivial to prevent separators from being assigned shortcut
keys, but this would eliminate one potentially useful use case: having
a large menu and using shortcut keys to jump to a section within the
menu.
Fix by treating a shortcut key on a separator as equivalent to "select
the separator, then press the down arrow key". This has the effect of
moving to the first non-separator menu item following the specified
separator, which is probably the most intuitive behaviour. (The
existing logic for moving the selection already handles the various
nasty corner cases such as a menu ending with one or more separators.)
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Unrecognised keys may be returned by getkey() as character code zero,
which currently matches against the first menu item with no shortcut
key defined.
Prevent this unintended behaviour by explicitly checking that the menu
item has a defined shortcut key.
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The output->buf field is a pointer, not an array, so sizeof() is not
applicable. We must use the allocated string length instead.
Identified by gcc:
util/zbin.c: In function ‘alloc_output_file’:
util/zbin.c:146:37: warning: argument to ‘sizeof’ in ‘memset’ call
is the same expression as the destination; did you mean to
dereference it? [-Wsizeof-pointer-memaccess]
memset ( output->buf, 0xff, sizeof ( output->buf ) );
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some PXE stacks are known to claim that IRQs are supported, but then
never generate interrupts. No satisfactory solution has been found to
this problem; the workaround is to add the PCI vendor and device IDs
to a list of devices which will be treated as simply not supporting
interrupts.
This is something of a hack, since it will generate false positives
for identical devices with a working PXE stack (e.g. those that have
been reflashed with iPXE), but it's an improvement on the current
situation.
Reported-by: Richard Moore <rich@richud.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some NICs (e.g. Hermon) provide hardware support for stripping the
VLAN tag, but do not provide any way for this support to be disabled.
Drivers for this hardware must therefore call vlan_find() to identify
a suitable receiving network device.
Provide a weak version of vlan_find() which will always return NULL if
VLAN support has not been enabled (either directly, or by enabling
a feature such as FCoE which requires VLAN support). This allows the
VLAN code to be omitted from builds where the user has not requested
support for VLANs.
Inspired-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iBFT NIC section has a VLAN field which must be filled in so that
iSCSI booting works over VLANs.
Unfortunately it is unclear from the IBM specification linked in
ibft.c whether the VLAN field is just the 802.1Q VLAN Identifier or
the full 802.1Q TCI. For now just fill in the VID, the Priority Code
Point and Drop Eligible Indicator could be set in the future if it
turns out they should be present too.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iBFT has a VLAN field that should be filled in. Add the
vlan_tag() function to extract the VLAN tag of a network device.
Since VLAN support is optional, define a weak function that returns 0
when iPXE is built without VLAN support.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Authenticode requires that the size of the raw file must equal the
size of the OptionalHeader.SizeOfHeaders plus the sum of all sections'
SizeOfRawData.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow non-data records to be split across multiple received I/O
buffers, to accommodate large certificate chains.
Reported-by: Nicola Volpini <Nicola.Volpini@kambi.com>
Tested-by: Nicola Volpini <Nicola.Volpini@kambi.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EFI's device naming model requires drivers to provide names for child
devices. Allow the driver's GetControllerName() method to delegate to
an instance of EFI_COMPONENT_NAME2_PROTOCOL installed on the child
device itself (if present); this allows the SNP device to expose its
own device name via the PCI driver's GetControllerName() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At present, loading a bzImage via iPXE requires enough RAM to hold two
copies of each initrd file. Remove this constraint by rearranging the
initrds in place.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
No code from the original source remains within this file; relicense
under GPL2+ with a new copyright notice.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The version number string is currently updated only if version.o
happens to be rebuilt due to changes in its dependencies. Add a
dependency upon the git index, so that the version number is updated
after any checkout.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Using -fno-dwarf2-cfi-asm is not sufficient to prevent the .eh_frame
section from being generated on newer versions of gcc. Add
-fno-exceptions -fno-unwind-tables -fno-asynchronous-unwind-tables;
this is sufficient to inhibit the .eh_frame section on gcc 4.7.1.
This does not affect the overall binary size, but does fix the numbers
reported by "size" for individual object files.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Current versions of gcc require -maccumulate-outgoing-args if any
sysv_abi functions call ms_abi functions. This requirement is likely
to be lifted in future gcc versions, so test explicitly to see if the
current version of gcc requires -maccumulate-outgoing-args.
This problem is currently masked since the implied
-fasynchronous-unwind-tables (which is the default in current gcc
versions) implies -maccumulate-outgoing-args.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 947976d ("[netdevice] Do not force a poll on net_tx()")
requires network devices to have TX rings that are sufficiently large
to allow a transmitted response to all packets received during a
single poll.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Intel NIC emulation in some versions of VMware seems to suffer
from a flaw whereby the Interrupt Cause Register (ICR) fails to assert
the usual "packet received" bit (ICR.RXT0) if a receive overflow
(ICR.RXO) has also occurred.
Work around this flaw by polling for completed descriptors whenever
either ICR.RXT0 or ICR.RXO is asserted.
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Debugged-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Tested-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid memory leaks by clearing any (non-child) settings immediately
before unregistering the network device settings block.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When prompting the user to enter a setting value via the "read"
command, prefill the input buffer with the setting's current value.
Requested-by: Ján Ondrej (SAL) <ondrejj@salstar.ks>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Including a netdev_poll() within net_tx() can cause the net_step()
loop to end up processing hundreds or thousands of packets within a
single step, since each received packet being processed may trigger a
response which, in turn causes a poll for further received packets.
Network devices must now ensure that the TX ring is at least as large
as the RX ring, in order to avoid running out of TX descriptors. This
should not cause any problems; unlike the RX ring, there is no
substantial memory cost incurred by increasing the TX ring size.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the newline from the "Press Ctrl-B..." prompt string, so that
prompt() does not attempt to backspace beyond the start of the line.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 5ad445f ("[settings] Treat an empty formatted value as meaning
"delete setting"") (re)defined the semantics of storing an empty
formatted setting as meaning "delete setting".
Remove the existing self-test using an empty formatted hex setting
value, since it no longer conforms to the defined semantics.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Take ownership from the ARP cache at the start of arp_destroy(), to
ensure that no code path can lead to arp_destroy() being re-entered.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
serial_console_init() would enable serial console support without
knowing if the serial driver succeeded or not. As a result, the
serial console would interfere with a normal keyboard on a system
lacking serial support.
Reported-by: Jan ONDREJ (SAL) <ondrejj(at)salstar.sk>
Signed-off-by: Shao Miller <sha0.miller@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 73eb3f1 ("[int13] Zero all possible registers when jumping to a
boot sector") introduced a regression preventing the SAN-booting of
boot sectors which rely upon %dl containing the correct drive number
(such as most CD-ROM boot sectors).
Fix by not zeroing %edx.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
TLS servers are not obliged to implement the RFC3546 maximum fragment
length extension, and many common servers (including OpenSSL, as used
in Apache's mod_ssl) do not do so. iPXE may therefore have to cope
with TLS records of up to 16kB. Allocations for 16kB have a
non-negligible chance of failing, causing the TLS connection to abort.
Fix by maintaining the received record as a linked list of I/O
buffers, rather than a single contiguous buffer. To reduce memory
pressure, we also decrypt in situ, and deliver the decrypted data via
xfer_deliver_iob() rather than xfer_deliver_raw().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
eIPoIB requires space to expand a transmitted ARP packet. This
guarantee is met by ensuring that a transmitted packet consists of at
least MAX_LL_HEADER_LEN bytes from the start of the I/O buffer up to
the end of the link-layer header, and at least IOB_ZLEN bytes
thereafter.
Adjust the I/O buffer allocation for SNP transmitted packets to ensure
that this guarantee is met.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At least one boot sector (the DUET boot sector used for bootstrapping
EFI from a non-EFI system) fails to initialise the high words of
registers before using them in calculations, leading to undefined
behaviour.
Work around such broken boot sectors by explicitly zeroing the
contents of all registers apart from %cs:%ip and %ss:%sp.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When fetching a named setting using a name that does not explicitly
specify a type, default to using the type stored when the setting was
created, rather than always defaulting to "string". This allows the
behaviour of user-defined settings to match the behaviour of
predefined settings (which have a sensible default type).
For example:
set server:ipv4 192.168.0.1
echo ${server}
will now print "192.168.0.1", rather than trying to print out the raw
IPv4 address bytes as a string.
The downside of this change is that existing tricks for printing
special characters within scripts may require (backwards-compatible)
modification. For example, the "clear screen" sequence:
set esc:hex 1b
set cls ${esc}[2J
echo ${cls}
will now have to become
set esc:hex 1b
set cls ${esc:string}[2J # Must now explicitly specify ":string"
echo ${cls}
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Almost all clients of the raw-packet interfaces (UNDI and SNP) can
handle only Ethernet link layers. Expose an Ethernet-compatible link
layer to local clients, while remaining compatible with IPoIB on the
wire. This requires manipulation of ARP (but not DHCP) packets within
the IPoIB driver.
This is ugly, but it's the only viable way to allow IPoIB devices to
be driven via the raw-packet interfaces.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow for allocation of memory blocks having a specified offset from a
specified physical alignment, such as being 12 bytes before a 2kB
boundary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards seem to drive the EEPROM CS line high (i.e. active)
when 9346CR.EEM is set to "normal operating mode", with the result
that the CS line is never deasserted. The symptom of this is that the
first read from the EEPROM will work, while all subsequent reads will
return garbage data.
Reported-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up advertising
only 100Mbps, despite being capable of 1000Mbps. Forcibly enable
advertisement of 1000Mbps on any RTL8169-like card.
This change relies on the assumption that the CTRL1000 register will
not exist on 100Mbps-only RTL8169 cards such as the RTL8101.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) crash and burn if DAC
is enabled, even if only 32-bit addresses are used. Observed
behaviour includes system lockups and repeated transmission of garbage
data onto the wire.
This seems to be a known problem. The Linux r8169 driver disables DAC
by default and provides a "use_dac" module parameter.
There appears to be no known test for determining whether or not DAC
will work. As a workaround, enable DAC only if we are built as as
64-bit binary. This at least eliminates the problem in the common
case of a 32-bit build, which will never use 64-bit addresses anyway.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some bits in the C+ Command register are always one. Testing for the
presence of the register must allow for this.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with
TCR.MXDMA set to 16 bytes. While this does not prevent proper
operation, it almost certainly degrades performance.
Fix by explicitly setting TCR.MXDMA to "unlimited".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with invalid
values in RCR.RXFTH and RCR.MXDMA, causing receive DMA to fail. Fix
by setting explicit values for both fields.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some RTL8169 cards (observed with an RTL8169SC) power up with garbage
values in the ring address registers, and do not clear the registers
on reset.
Fix by always setting the high dword of the ring address registers.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 501527d ("[http] Treat any unexpected connection close as an
error") introduced a regression causing HTTP SAN booting to fail. At
the end of the response to the HEAD request, the call to http_done()
would erroneously believe that the server had disconnected in the
middle of the HTTP headers.
Fix by treating the header block from a HEAD request as a trailer
block. This fixes the problem and also simplifies the logic in
http_rx_header().
Reported-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The FTP SIZE command allows us to get the size of a particular file,
as a consequence, we can now show proper transfer progression while
fetching a file using the FTP protocol.
Signed-off-by: Marin Hannache <git@mareo.fr>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently checks that the server has not closed the connection
mid-stream (i.e. in the middle of a chunked transfer, or before the
specified Content-Length has been received), but does not check that
the server got as far as starting to send data. Consequently, if the
server closes the connection before any data is transferred (e.g. if
the server gives up waiting while iPXE performs the validation steps
for TLS), then iPXE will treat this as a successful transfer of a
zero-length file.
Fix by checking the RX connection state, and forcing an error if the
server has closed the connection at an unexpected point.
Originally-fixed-by: Marin Hannache <mareo@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The UNDI ROM header does contain a checksum byte. Apparently no-one
cares about this, since iPXE has left it as zero for years without
anyone noticing.
Since Option::ROM now understands the UNDI ROM header, we may as well
fix up the checksum byte for the sake of completeness.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Option::ROM currently understands only JMP NEAR and JMP SHORT
instructions in the initialisation entry point. At least one Broadcom
option ROM has been observed to use a CALL NEAR instruction.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
COMBOOT images are detected by looking for a ".com" or ".cbt" filename
extension. There are widely-used files with a ".com" extension, such
as "wdsnbp.com", which are PXE images rather than COMBOOT images.
Avoid false detection of PXE images as COMBOOT images by accepting
only a ".cbt" extension as indicating a COMBOOT image.
Interestingly, this bug has been present for a long time but was
frequently concealed because the filename was truncated to fit the
fixed-length "name" field in struct image. (PXE binaries ending in
".com" tend to be related to Windows deployment products and so often
use pathnames including backslashes, which iPXE doesn't recognise as a
path separator and so treats as part of a very long filename.)
Commit 1c127a6 ("[image] Simplify image management commands and
internal API") made the image name a variable-length field, and so
exposed this flaw in the COMBOOT image detection algorithm.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the file mode to be specified using a "mode=" command line
parameter. For example:
initrd http://web/boot/bootlocal.sh /opt/bootlocal.sh mode=755
Requested-by: Bryce Zimmerman <bryce.zimmerman@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some AMI BIOSes apparently break in exciting ways when asked for PMM
allocations for sizes that are not multiples of 4kB.
Fix by rounding up the image source area to the nearest 4kB. (The
temporary decompression area is already rounded up to the nearest
128kB, to facilitate sharing between multiple iPXE ROMs.)
Reported-by: Itay Gazit <itayg@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Change the DMA alignment from 4096 bytes to 16 bytes, to conserve
available DMA memory. The hardware doesn't have any specific
alignment requirements.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reduce CPU usage while waiting for user input. This is particularly
important for virtual machines, where CPU is a shared resource.
Reported-by: Alessandro Salvatori <alessandro@embrane.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Cygwin's assembler treats '/' as a comment character.
Reported-by: Steve Goodrich <steve.goodrich@se-eng.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Similarly to FreeBSD, OpenBSD requires the object format to be
specified as elf_i386_obsd rather than elf_i386.
Reported-by: Jiri B <jirib@devio.us>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
PCI3.0 allows us to report a "runtime size" which can be smaller than
the actual ROM size. On systems that support PMM our runtime size
will be small (~2.5kB), which helps to conserve the limited option ROM
space. However, there is no guarantee that the PMM allocation will
succeed, and so we need to report the worst-case runtime size in the
PCI header.
Move the "shrunk ROM size" field from the PCI header to a new "iPXE
ROM header", allowing it to be accessed by ROM-manipulation utilities
such as disrom.pl.
Reported-by: Anton D. Kachalov <mouse@yandex-team.ru>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Datasheet pp. 41-42 defines 'rx packet length' as upper word of
'status' dword field of the receive descriptor table.
http://www.smsc.com/media/Downloads_Archive/discontinued/83c171.pdf
Tested on SMC EtherPower II.
Signed-off-by: Alexey Smazhenko <darkover@corbina.com.ua>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
gcc 4.7 produces a spurious warning about an array subscript being out
of bounds. Use a pointer dereference instead of an array lookup to
inhibit this spurious warning.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Simplify the process of booting by ensuring that old images are not
left registered after an unsuccessful autoboot attempt.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose image tail-recursion to iPXE scripts via the "--replace"
option. This functions similarly to exec() under Unix: the
currently-executing script is replaced with the new image (as opposed
to running the new image as a subroutine).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The script include/ipxe/efi/import.pl relies on a particular format
for the #include guard in order to detect EFI headers that are not
imported.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
PXENV_FILE_CMDLINE is an iPXE extension, and will not be supported by
most PXE stacks. Do not report any errors to the user, since in
almost all cases the error will mean simply "not loaded by iPXE".
Reported-by: Patrick Domack <patrickdk@patrickdk.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The EFI_CPU_IO_PROTOCOL is not available on all EFI platforms. In
particular, it is not available under OVMF, as used for qemu.
Since the EFI_CPU_IO_PROTOCOL is an abomination of unnecessary
complexity, banish it and use raw I/O instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Attempt to restore the network device to the state it was in prior to
calling the NBP. This simplifies the task of taking follow-up action
in an iPXE script.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow scripts to report errors in more detail by exposing the most
recent error via the ${errno} setting. For example:
chain ${filename} || goto failed
...
:failed
imgfree http://192.168.0.1/ipxe_error.php?error=${errno}
Note that ${errno} is valid only immediately after executing a failed
command.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some BIOSes (observed on a Supermicro system with an AMI BIOS) seem to
use the area immediately below 0x7c00 to store data related to the
boot process. This data is currently liable to be overwritten by the
temporary stack used while decompressing and installing iPXE.
Try to avoid any such problems by placing the temporary stack
immediately after the loaded iPXE binary. Any memory used by the
stack could then potentially have been overwritten anyway by a larger
binary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On i350 the datasheet contradicts itself in stating that the default
value of RXDCTL.ENABLE for queue zero is both set (according to the
"Receive Initialization" section) and unset (according to the "Receive
Descriptor Control - RXDCTL" section). Empirical evidence suggests
that the default value is unset.
Explicitly enable both transmit and receive queues to avoid any
ambiguity.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On 82576 (and probably others), the datasheet states that "the tail
register of the queue (RDT[n]) should not be bumped until the queue is
enabled". There is some confusion over exactly what constitutes
"enabled": the initialisation blurb says that we should "poll the
RXDCTL register until the ENABLE bit is set", while the description
for the RXDCTL register says that the ENABLE bit is set by default
(for queue zero). Empirical evidence suggests that the ENABLE bit
reads as set immediately after writing to RCTL.EN, and so polling is
not necessary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The setup_move_size field is not defined in protocol versions earlier
than 2.00 (and is obsolete in versions later than 2.01). In binaries
using versions earlier than 2.00, the relevant location is likely to
contain executable code.
Interestingly, this bug has been present since support for pre-2.00
protocol versions was added in 2009, and has been unexpectedly
modifying the memtest86+ code fragment:
mov $0x92, %dx
inb %dx, %al
Fortuitously, the modification exactly overwrote the value loaded into
%dx, and so the net effect was limited to causing Fast Gate A20
detection to always fail.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A window size of 256kB should be sufficient to allow for
full-bandwidth transfers over a Gigabit LAN, and for acceptable
transfer speeds over other typical links.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The maximum TCP throughput is fundamentally limited by the amount of
available receive buffer space. Increase the heap size from 128kB to
512kB to allow the use of larger TCP windows.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Whenever memory pressure causes a queued packet to be discarded (and
so retransmitted), reduce the maximum TCP window to a size that would
have prevented the discard.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Discarding the active ARP cache entry in the middle of a download will
substantially disrupt the TCP stream. Try to minimise any such
disruption by treating ARP cache entries as expensive, and discarding
them only when nothing else is available to discard.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
I/O buffers are allocated on aligned boundaries. The I/O buffer
descriptor (the struct io_buffer) is currently attached to the end of
the I/O buffer. When the size of the buffer is close to its
alignment, this can waste large amounts of aligned memory.
For example, a network card using 2048-byte receive buffers will end
up allocating 2072 bytes on a 2048-byte boundary. This effectively
wastes 50% of the available memory.
Improve the situation by allocating the descriptor separately from the
main I/O buffer if inline allocation would cause the total allocated
size to cross the alignment boundary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current logic is to process at most one received packet per call
to net_poll(), on the basis that refilling the hardware descriptor
ring should be delayed as little as possible. However, this limits
the rate at which packets can be processed and ultimately ends up
adding latency which, in turn, limits the achievable throughput.
With temporary modifications in place to essentially remove all
resource constraints (heap size increased to 16MB, RX descriptor ring
increased to 64 descriptors) and a TCP window size of 1MB, the
throughput on a gigabit (i.e. 119MBps) network can be observed to fall
off exponentially from around 115MBps to around 75MBps. Changing
net_poll() to process all received packets results in a steady
119MBps throughput.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 196751c ("[build] Enable warnings when building utilities")
revealed a previously hidden compiler warning in util/nrv2b.c
regarding an out-of-bounds array subscript in the code
#if defined(SWD_BEST_OFF)
if (s->best_pos[2] == 0)
s->best_pos[2] = key + 1;
#endif
where best_pos[] is defined by
#define SWD_BEST_OFF 1
#if defined(SWD_BEST_OFF)
unsigned int best_off[ SWD_BEST_OFF ];
unsigned int best_pos[ SWD_BEST_OFF ];
#endif
With SWD_BEST_OFF set to 1, it can be proven that all code paths
referring to s->best_off[] and s->best_pos[] will never be executed,
with the exception of the two lines above. Since these two lines
alone can have no effect on execution, we can safely undefine
SWD_BEST_OFF.
Verified by comparing md5sums of bin/undionly.kpxe before and after
the change.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Each ARP cache entry maintains a transmission queue, which is sent out
as soon as the link-layer address is known. If multiple packets are
queued, then it is possible for memory pressure to cause the ARP cache
discarder to be invoked during transmission of the first packet, which
may cause the ARP cache entry to be deleted before the second packet
can be sent. This results in an invalid pointer dereference.
Avoid this problem by reference-counting ARP cache entries and
ensuring that an extra reference is held while processing the
transmission queue, and by using list_first_entry() rather than
list_for_each_entry_safe() to traverse the queue.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit ea61075 ("[tcp] Add support for TCP window scaling") introduced
a potential NULL pointer dereference by referring to the connection's
send window scale before checking whether or not the connection is
known.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE currently aligns all I/O buffers on a 2kB boundary. This is
overkill for transmitted packets, which are typically much smaller
than 2kB.
Align I/O buffers on their own size. This reduces the alignment
requirement for small buffers, while preserving the guarantee that I/O
buffers will never cross boundaries that might cause problems for some
DMA engines.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The default maximum plaintext fragment length for TLS is 16kB, which
is a substantial amount of memory for iPXE to have to allocate for a
temporary decryption buffer.
Reduce the memory footprint of TLS connections by requesting a maximum
fragment length of 2kB.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The maximum unscaled TCP window (64kB) implies a maximum bandwidth of
around 300kB/s on a WAN link with an RTT of 200ms. Add support for
the TCP window scaling option to remove this upper limit.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The undinet driver always has to make a copy of the received frame
into an I/O buffer. Align this copy sensibly so that subsequent
operations are as fast as possible.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Checking for keypresses takes a non-negligible amount of time, and
measurably affects our RTT. Minimise the impact by checking for
keypresses only once per timer tick.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The generic TCP/IP checksum implementation requires approximately 10
CPU clocks per byte (as measured using the TSC). Improve this to
approximately 0.5 CPU clocks per byte by using "lodsl ; adcl" in an
unrolled loop.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Calculating the TCP/IP checksum on received packets accounts for a
substantial fraction of the response latency.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "rep" prefix can be used with an iteration count of zero, which
allows the variable-length memcpy() to be implemented without using
any conditional jumps.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A reasonably large (512MB) file transferred via HTTP over Gigabit
Ethernet should complete in around 4.6 seconds. Increase the
resolution of the "time" command to tenths of a second, to allow such
transfers to be meaningfully measured.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hw pointer in PCI driver data as expected by sky2_remove().
Signed-off-by: Valentine Barshak <gvaxon@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE has no concept of the local time zone, mainly because there is no
viable way to obtain time zone information in the absence of local
state. This causes potential problems with newly-issued certificates
and certificates that are about to expire.
Avoid such problems by allowing an error margin of around 12 hours on
certificate validity periods, similar to the error margin already
allowed for OCSP response timestamps.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
FCoE requires the use of multiple local unicast link-layer addresses.
To avoid the complexity of managing multiple addresses, iPXE operates
in promiscuous mode. As a consequence, any unicast packets with
non-matching IPv4 addresses are rejected at the IPv4 layer (rather
than at the link layer).
This can cause problems when issuing a second DHCP request: if the
address chosen by the DHCP server does not match the existing address,
then the DHCP response will itself be rejected.
Fix by requesting a broadcast response from the DHCP server if the
network interface already has any IPv4 addresses.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
PMM defines the return code 0xffffffff as meaning "unsupported
function". It's hard to imagine a PMM BIOS that doesn't support
pmmAllocate(), but apparently such things do exist.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A .mrom image currently assumes that it is the first image within the
expansion ROM BAR, which may not be correct when multiple images are
present.
Fix by scanning through the BAR until we locate an image matching our
build ID.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The header of a .mrom image declares its length to be only a few
kilobytes; the remainder is accessed via a sideband mechanism. This
makes it difficult to append an additional ROM image, such as an EFI
ROM.
Add a second, dummy ROM header covering the payload portion of the
.mrom image, allowing consumers to locate any appended ROM images in
the usual way.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid potential confusion in the documentation by using a
vendor-neutral name for the extended (AMD-defined) feature set.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add "sync" command (loosely based on the Unix "sync"), which will wait
for any pending operations to complete.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE is fundamentally asynchronous in operation: some operations
continue in the background even after the foreground has continued to
a new task. For example, the closing FIN/ACK exchanges of a TCP
connection will take place in the background after an HTTP download
has completed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide HTTP Basic authentication credentials only in response to a
401 Unauthorized response from the server.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some headers can modify the meaning of the response code. For
example, a WWW-Authenticate header can change the interpretation of a
401 Unauthorized response from "Access denied" to "Please
authenticate".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The setting name "key" conflicts with the setting name "key" already
in use by the 802.11 code. Resolve the conflict by renaming the newer
setting to "privkey".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
EFI_PCI_DEVICE_ENABLE is a list of the standard attributes that must
be enabled for a PCI device to function: I/O cycles, memory cycles,
and bus-mastering. We currently call EFI_PCI_IO_PROTOCOL::Attribute()
with the parameter EFI_PCI_DEVICE_ENABLE to enable a PCI device. This
should translate to a single write to PCI configuration space.
Simplicity is not a virtue within the UEFI world. Some platforms will
'helpfully' report an error if EFI_PCI_DEVICE_ENABLE is used on a
device that doesn't actually support all three of the relevant
attributes. For example, if a PCI device provides only memory-mapped
accesses (and so hardwires the I/O enable bit to zero), then using
EFI_PCI_DEVICE_ENABLE on such a platform will result in an
EFI_UNSUPPORTED error.
There is no plausible use case in which it is useful for the platform
to return an error in this way, and doing so makes it impossible to
distinguish genuine errors from noise.
Work around this broken behaviour by attempting to enable the three
attributes individually, and ignoring any errors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iSCSI generally includes a full SCSI response only when an error
occurs. iscsi_scsi_done() currently passes the NULL response through
to scsi_response(), which ends up causing scsicmd_response() to
dereference a NULL pointer.
Fix by calling scsi_response() only if we have a non-NULL response.
Reported-by: Brendon Walsh <brendonwalsh@niamu.com>
Tested-by: Brendon Walsh <brendonwalsh@niamu.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for constructing OCSP queries and parsing OCSP responses.
(There is no support yet for actually issuing an OCSP query via an
HTTP POST.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
X.509 certificate processing currently produces an overwhelming amount
of debugging information. Move some of this from DBGLVL_LOG to
DBGLVL_EXTRA, to make the output more manageable.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Automatically attempt to download any required cross-signing
certificates from http://ca.ipxe.org/auto, in order to enable the use
of standard SSL certificates issued by public CAs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
To allow for automatic download of cross-signing certificates and for
OCSP, the validation of certificates must be an asynchronous process.
Create a stub validator which uses a job-control interface to report
the result of certificate validation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
CMS includes an unordered certificate set, from which certificates
must be extracted in order by matching up issuers with subjects. We
will use the same functionality as part of the automatic download of
cross-signing certificates. Generalise cms_find_subject() to
x509_find_subject(), and create x509_auto_append().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At present, certificate chain validation is treated as an
instantaneous process that can be carried out using only data that is
already in memory. This model does not allow for validation to
include non-instantaneous steps, such as downloading a cross-signing
certificate, or determining certificate revocation status via OCSP.
Redesign the internal representation of certificate chains to allow
chains to outlive the scope of the original source of certificates
(such as a TLS Certificate record).
Allow for certificates to be cached, so that each certificate needs to
be validated only once.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The free-memory-block traversal code triggers multiple warnings from
Valgrind when assertions are enabled, since the list consistency
checks performed by list_check() end up accessing areas that have been
marked as inaccessible.
Fix by ensuring that any memory areas that will be accessed by
list_check() are marked as defined when necessary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
RTL8139C+ cards use essentially the same datapath as RTL8169, which is
zerocopy and 64-bit capable. Older RTL8139 cards use a single receive
ring buffer rather than a descriptor ring, but still share substantial
amounts of functionality with RTL8169.
Include support for RTL8139 cards within the generic Realtek driver,
since there is no way to differentiate between RTL8139 and RTL8139C+
cards based on the PCI IDs alone.
Many thanks to all the people who worked on the rtl8139 driver over
the years.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If a root certificate has been explicitly specified at build time
using TRUST=/path/to/cert then do not allow this to be overridden even
from a trustworthy settings source (such as VMware GuestInfo).
Similarly, if a client certificate (and private key) has been
explicitly specified at build time, then do not allow it to be
overridden at runtime.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some objects (embedded.o, rootcert.o, and clientcert.o) define
additional dependencies on external files, using syntax such as:
$(BIN)/clientcert.o : $(CERT_LIST)
This dependency can be missed when using debug builds. For example,
if DEBUG=clientcert is used, then the relevant object is
$(BIN)/clientcert.dbg1.o rather than $(BIN)/clientcert.o.
Fix by adding dependencies to $(clientcert_DEPS) instead:
clientcert_DEPS += $(CERT_LIST)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
util/prototester.c was removed in commit a6d1815 ("Obsolete for some
time now") back in 2006.
Signed-off-by: Marin Hannache <mareo@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The WinCE, a.out and FreeBSD loaders are designed to be #included by
core/loader.c, which no longer exists. These old loaders are not
usable anymore and cause compilation failures when enabled in
config/general.h.
Signed-off-by: Marin Hannache <mareo@mareo.fr>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
http_step() allocates a potentially large block of storage (since the
URI can be arbitrarily long), and can be invoked as part of an already
deep call stack via xfer_window_changed().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
xfer_printf() occasionally has to deal with strings that are
potentially long, such as HTTP URIs with multiple query parameters.
Allocating these on the stack can lead to stack overruns and memory
corruption.
Fix by using vasprintf() instead of a stack allocation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The link state is currently set at probe time, and updated only when
the device is polled. This results in the user seeing a misleading
stale "Link: down" message, if autonegotiation did not complete within
the short timespan of the probe routine.
Fix by updating the link state when the device is opened, so that the
message that ends up being displayed to the user reflects the real
link state at device open time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If the network interface has only just been opened (e.g. by the "dhcp"
command) then we should allow at least one opportunity for the card to
update the link state before testing it, to avoid false positives.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There is no explicit SNP API call to determine link state; the SNP
interface user may check the MediaPresent field within the mode data
at any time.
Update the MediaPresent field whenever the link state changes.
Reported-by: Michael R Turner <mikeyt@us.ibm.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Changing the trusted root certificate currently requires a rebuild of
the iPXE binary, which may be inconvenient or impractical.
Allow the list of trusted root certificate fingerprints to be
overridden using the "trust" setting, but only at the point of iPXE
initialisation. This prevents untrusted sources of settings
(e.g. DHCP) from subverting the chain of trust, while allowing
trustworthy sources to change the trusted root certificate without
requiring a rebuild.
The basic idea is that if you are able to manipulate a trustworthy
source of settings (e.g. VMware GuestInfo or non-volatile stored
options), then you would be able to replace the iPXE binary anyway,
and so no security is lost by allowing such sources to override the
list of trusted root certificates.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Solaris assumes that there is enough space above the Multiboot modules
to use as a decompression and scratch area. This assumption is
invalid when using iPXE, which places the Multiboot modules near the
top of (32-bit) memory.
Fix by copying the modules to an area of memory immediately following
the loaded kernel.
Debugged-by: Michael Brown <mcb30@ipxe.org>
Debugged-by: Scott McWhirter <scottm@joyent.com>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE provides no support for manually configuring the link speed.
Provide a generic routine which should be able to reset any MII/GMII
PHY and enable autonegotiation.
Prototyped-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
niclist.pl recursively scans specified source folders and builds a
list of supported NICs by looking for ISA_ROM and PCI_ROM lines and
outputs the list in text, CSV, JSON, HTML or DokuWiki format. Sorting
and column selection is possible.
The pci-utils pci.ids file is fetched from SourceForge once a day to
also output the "official" vendor/device names associated with the PCI
device.
Signed-off-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow iPXE settings to be specified in the .vmx file via the VMware
GuestInfo mechanism. For example:
guestinfo.ipxe.filename = "http://boot.ipxe.org/demo/boot.php"
guestinfo.ipxe.dns = "192.168.0.1"
guestinfo.ipxe.net0.ip = "192.168.0.15"
guestinfo.ipxe.net0.netmask = "255.255.255.0"
guestinfo.ipxe.net0.gateway = "192.168.0.1"
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow TFTP to be configured out by moving the next-server setting
definition (which is used by autoboot.c) from tftp.c to settings.c.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Refactor setting type handlers to parse and format values, rather than
storing and fetching formatted values.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Solaris kernels seem to rely on having the full kernel path present in
the multiboot command line; if only the kernel name is present then
the boot fails with the error message
krtld: failed to open 'unix'
Debugged-by: Michael Brown <mcb30@ipxe.org>
Debugged-by: Scott McWhirter <scottm@joyent.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
DOWNLOAD_PROTO_TFTM is now useless as tftm support has been merged
into tftp.c. DOWNLOAD_PROTO_TFTP should be used instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for 82579-based chips such as those found on Sandy Bridge
motherboards. Based on d3738bb8203acf8552c3ec8b3447133fc0938ddd in
Linux.
Signed-off-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
sizeof(cipherspec) is obviously wrong in this context, because it will
only zero the first 4 or 8 bytes (cipherspec is a pointer).
This problem was reported by cppcheck.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use explicit size in memset because 8 bytes must be set always.
This problem was reported by cppcheck.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Using __from_text16() and __from_data16() in inline asm constraints
sometimes defeats gcc's ability to simplify expressions down to
compile-time constants.
Reported-by: Jason Kohles <jkohles@palantir.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE's support for COMBOOT images is now quite outdated; it has not
kept up to date with changes in the COMBOOT API. The primary use for
COMBOOT seems to be for menuing support. Now that we have native iPXE
script-based menus, COMBOOT support can be gracefully retired (with
immense thanks to Daniel Verkamp for having successfully implemented
such an ambitious feature many years ago).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The "no" keymap is for a Dvorak keyboard.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
I am unable to find any definitive documentation on how Linux keyboard
symbols work. In the absence of any documentation, I'm going to
assume that unexpected keysyms are harmless and should be ignored.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At present, we always hide an extra sizeof(struct external_memory), to
account for the header on the lowest allocated block. This header
ceases to exist when there are no allocated blocks remaining.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use a private ANSI escape sequence to convey the priority of an
internal syslog() message through to the syslog server.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
An ANSI escape sequence context cannot be shared between multiple
users. Make the ANSI escape sequence context part of the line console
definition and provide individual contexts for each user.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide an internal syslog() function (unrelated to the syslog
console) which can be used to create log messages with specified
priorities.
The build-time constant LOG_LEVEL can be used to select the minimum
required priority for log messages. Any messages that do not have a
sufficient priority will be ignored (and will be optimised away at
compile-time).
The default LOG_LEVEL is LOG_NONE.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The output from text-based user interfaces such as the "config"
command is not generally meaningful for logfile-based consoles such as
syslog and vmconsole.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the concept of a "console usage", such as "standard output" or
"debug messages". Allow usages to be associated with each console
independently. For example, to send debugging output via the serial
port, while preventing it from appearing on the local console:
#define CONSOLE_SERIAL CONSOLE_USAGE_ALL
#define CONSOLE_PCBIOS ( CONSOLE_USAGE_ALL & ~CONSOLE_USAGE_DEBUG )
If no usages are explicitly specified, then a default set of usages
will be applied. For example:
#define CONSOLE_SERIAL
will have the same affect as
#define CONSOLE_SERIAL CONSOLE_USAGE_ALL
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the name, cmdline, and action parameters from imgdownload() and
imgdownload_string(). These functions now simply download and return
an image.
Add the function imgacquire(), which will interpret a "name or URI
string" parameter and return either an existing image or a newly
downloaded image.
Use imgacquire() to merge similar image-management commands that
currently differ only by whether they take the name of an existing
image or the URI of a new image to download. For example, "chain" and
"imgexec" can now be merged.
Extend imgstat and imgfree commands to take an optional list of
images.
Remove the arbitrary restriction on the length of image names.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Trusted images may always be executed. Untrusted images may be
executed only if the current image trust requirement allows untrusted
images.
Images can be marked as trusted using image_trust(), and marked as
untrusted using image_untrust().
The current image trust requirement can be changed using
image_set_trust(). It is possible to make the change permanent, in
which case any future attempts to change the image trust requirement
will fail.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There is no INT 10 call for "display character with attribute,
advancing the cursor and scrolling the screen as necessary". We
therefore make two INT 10 calls: INT 10,09 to write the character with
its attribute at the current cursor position, and then INT 10,0e to
(re)write the character (leaving the attribute unchanged), advance the
cursor position and scroll as necessary.
This confuses the serial-over-LAN console redirection feature provided
by some BIOSes.
Fix by performing the INT10,09 only when necessary to change the
existing attribute.
Reported-by: Itay Gazit <itaygazit@gmail.com>
Tested-by: Itay Gazit <itaygazit@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Cryptographic Message Syntax (PKCS#7) provides a format for
encapsulating digital signatures of arbitrary binary blobs. A
signature can be generated using
openssl cms -sign -in <file to sign> -binary -noattr \
-signer <signer>.crt -inkey <signer>.key -certfile <CA>.crt \
-outform DER -out <signature>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The certificate may be part of an ASN.1-encoded certificate chain, and
so may not be the only object contained within the ASN.1 cursor.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
asn1_skip() will return an error on reaching the end of an object, and
so should not be used as the basis for asn1_shrink().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The concept of an OID-identified algorithm as defined in X.509 is used
in some other standards (e.g. PKCS#7). Generalise this functionality
and provide it as part of the ASN.1 core.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
OIDs are theoretically part of a global hierarchy. However, the
hierarchy is sufficiently disorganised as to be essentially
meaningless for all purposes other than guaranteeing uniqueness.
Ignore the hierarchical nature of OIDs and treat them as opaque.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow a client certificate and corresponding private key to be
specified at build time using the syntax
make CERT=/path/to/certificate KEY=/path/to/key
The build process uses openssl to convert the files into DER format,
and includes them within the client certificate store in
clientcert.c. The build process will prompt for the private key
password if applicable.
Note that the private key is stored unencrypted, and so the resulting
iPXE binary (and the temporary files created during the build process)
should be treated as being equivalent to an unencrypted private key
file.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Simplify code by recording the active handshake digest algorithm as a
session parameter. (Note that we must still accumulate digests for
all supported algorithms, since we don't know which digest will
eventually be used until we receive the Server Hello.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
TLSv1.1 and earlier use a hybrid of MD5 and SHA-1 to generate digests
over the handshake messages. Formalise this as a separate digest
algorithm "md5+sha1".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Validate the server certificate against the trusted root certificate
store. The server must provide a complete certificate chain, up to
and including the trusted root certificate that is embedded into iPXE.
Note that the date and time are not yet validated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow trusted root certificates to be specified at build time using
the syntax
make TRUST=/path/to/certificate1,/path/to/certificate2,...
The build process uses openssl to calculate the SHA-256 fingerprints
of the specified certificates, and adds them to the root certificate
store in rootcert.c. The certificates can be in any format understood
by openssl.
The certificates may be server certificates or (more usefully) CA
certificates.
If no trusted certificates are specified, then the default "iPXE root
CA" certificate will be used.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
bigint_mod_multiply() and bigint_mod_exp() require a fixed amount of
temporary storage for intermediate results. (The amount of temporary
storage required depends upon the size of the integers involved.)
When performing calculations for 4096-bit RSA the amount of temporary
storage space required will exceed 2.5kB, which is too much to
allocate on the stack. Avoid this problem by forcing the caller to
allocate temporary storage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid a compiler warning on some versions of gcc by using real
function prototypes.
Reported-by: Rob Shelley <Rob@cirris.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
RSA requires modular exponentiation using arbitrarily large integers.
Given the sizes of the modulus and exponent, all required calculations
can be done without any further dynamic storage allocation. The x86
architecture allows for efficient large integer support via inline
assembly using the instructions that take advantage of the carry flag
(e.g. "adcl", "rcrl").
This implemention is approximately 80% smaller than the (more generic)
AXTLS implementation.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
All axTLS files are now vanilla versions of the upstream axTLS files,
with one minor exception: the unused "ctx" parameter of
bi_int_divide() has been marked with "__unused" to avoid a compilation
error.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
gcc will not warn about unused constant static variables. An unused
test declaration is almost certainly a bug, so ensure that warnings
are generated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Both HMAC_DRBG using SHA-1 and HMAC_DRBG using SHA-256 are Approved
algorithms in ANS X9.82 for our chosen security strength of 128 bits.
However, general recommendations (see e.g. NIST SP800-57) are to use a
larger hash function in preference to SHA-1.
Since SHA-256 is required anyway for TLSv1.2 support, there is no code
size penalty for switching HMAC_DRBG to also use SHA-256.
Signed-off-by: Michael Brown <mcb30@ipxe.org>