On i350 the datasheet contradicts itself in stating that the default
value of RXDCTL.ENABLE for queue zero is both set (according to the
"Receive Initialization" section) and unset (according to the "Receive
Descriptor Control - RXDCTL" section). Empirical evidence suggests
that the default value is unset.
Explicitly enable both transmit and receive queues to avoid any
ambiguity.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On 82576 (and probably others), the datasheet states that "the tail
register of the queue (RDT[n]) should not be bumped until the queue is
enabled". There is some confusion over exactly what constitutes
"enabled": the initialisation blurb says that we should "poll the
RXDCTL register until the ENABLE bit is set", while the description
for the RXDCTL register says that the ENABLE bit is set by default
(for queue zero). Empirical evidence suggests that the ENABLE bit
reads as set immediately after writing to RCTL.EN, and so polling is
not necessary.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use hw pointer in PCI driver data as expected by sky2_remove().
Signed-off-by: Valentine Barshak <gvaxon@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
RTL8139C+ cards use essentially the same datapath as RTL8169, which is
zerocopy and 64-bit capable. Older RTL8139 cards use a single receive
ring buffer rather than a descriptor ring, but still share substantial
amounts of functionality with RTL8169.
Include support for RTL8139 cards within the generic Realtek driver,
since there is no way to differentiate between RTL8139 and RTL8139C+
cards based on the PCI IDs alone.
Many thanks to all the people who worked on the rtl8139 driver over
the years.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The link state is currently set at probe time, and updated only when
the device is polled. This results in the user seeing a misleading
stale "Link: down" message, if autonegotiation did not complete within
the short timespan of the probe routine.
Fix by updating the link state when the device is opened, so that the
message that ends up being displayed to the user reflects the real
link state at device open time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE provides no support for manually configuring the link speed.
Provide a generic routine which should be able to reset any MII/GMII
PHY and enable autonegotiation.
Prototyped-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for 82579-based chips such as those found on Sandy Bridge
motherboards. Based on d3738bb8203acf8552c3ec8b3447133fc0938ddd in
Linux.
Signed-off-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Practically speaking, it seems the convention is to only have one
packet pending and not rely upon any mechanism to associate returned
txbuf with txqueue.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This function never did much in this driver anyway, and after commit
b5ed30b2 ("[tg3] Fix compilation on newer gcc versions") it became
apparent that its remaining functionality could be easily moved to
tg3_test_dma().
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the old Etherboot tg3 driver with a more up-to-date driver
using the iPXE API.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The RS bit is used to instruct the NIC to update the TX descriptor
status byte. The RPS bit is used to instruct the NIC to defer this
update until after the packet has been transmitted on the wire (rather
than merely read into the transmit FIFO).
The driver currently sets RPS but not RS. Some e1000 models seem to
interpret this as implying that the status byte should be updated;
some don't. On the ones that don't, we never see any TX completions
and so rapidly run out of TX buffers.
Fix by setting the RS bit in the TX descriptor. (We don't care about
when the packet reaches the wire, so don't bother setting the RPS
bit.)
Reported-by: Miroslav Halas <miroslav.halas@bankofamerica.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid spurious matches for peer key 0 against empty peer cache
entries, and set the LL_MULTICAST flag in addition to LL_BROADCAST.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The ChipCmd register is only an 8-bit register. The 16-bit access
used by iPXE was causing an issue when used with qemu emulated rtl8139
device which was improperly aligning IOs.
Signed-off-by: Julian Pidancet <julian.pidancet@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reported-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE operates the forcedeth NIC in promiscuous mode, and never changes
the unicast MAC address filter registers. We should not therefore set
the flag indicating (to other drivers loaded later) that the MAC
address order has already been corrected.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The forcedeth driver currently implements unicast MAC address
filtering in software. This is almost invariably the wrong thing to
do (since the network stack must already be able to cope with unwanted
packets) and it breaks FCoE (which requires the card to operate in
promiscuous mode).
Also, the implementation is buggy: is_local_ether_addr() is used to
check for a locally-assigned Ethernet address (not to check for a
unicast address), and the current link-layer address is in
netdev->ll_addr, not netdev->hw_addr.
Fix by removing this code.
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Tested-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid unused-but-set variable warning in gcc 4.6 which was introduced
by commit 9215b7f ("[forcedeth] Clear the MII link status register on
link status changes").
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose a function setting_applies() to allow a caller to determine
whether or not a particular setting is applicable to a particular
settings block.
Restrict DHCP-backed settings blocks to accepting only DHCP-based
settings.
Restrict network device settings blocks to accepting only DHCP-based
settings and network device-specific settings such as "mac".
Inspired-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
From a cursory examination, it appears as though the calculation of
tx_available is redundant, since eepro_transmit() waits for transmit
completion before returning anyway.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On reset and close, the ICR register is read to clear any pending
interrupts, but the value is simply ignored. Avoid assigning the
value to a variable, to inhibit a warning from gcc 4.6.
Also fix a potential race condition in reset routines which clear
interrupts before disabling them.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
These unused portions trigger a compiler warning under gcc 4.6, due to
the ambiguity over the "page" field in struct igbvf_buffer.
Reported-by: Ralph Giles <giles@thaumas.net>
Tested-by: Ralph Giles <giles@thaumas.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In a virtual environment such as qemu, we can legitimately receive
packets less than 64 bytes in length, such as ARP replies. These are
currently discarded, causing most IPv4 communication to fail.
Fix by ignoring the RFDShort bit when receiving packets.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Merge the "bus" and "devfn" fields into a single "busdevfn" field, to
match the format used by the majority of external code.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove duplicate hardware resets, remove network interface logic
reset.
This also fixes a bug where some 3c905C variants would return bogus
EEPROM values because of a too short delay after the network reset.
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Reported-by: Peter Huewe <peterhuewe@gmx.de>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
DBG is reserved for errors and important warnings only.
DBG2 for additional information, e.g. "received packet".
DBGP is used to print the name of every function as it is called.
Signed-off-by: Thomas Miletich<thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove the concept of shutdown exit flags, and replace it with a
counter used to keep track of exposed interfaces that require devices
to remain active.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support a new function mode "multi-function 8 Direct IO" which is used
in ESX Direct I/O configuration.
Update driver version to 3.5.0.1
Signed-off-by: Masroor Vettuparambil <masroor.vettuparambil@exar.com>
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@exar.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Since its implementation several years ago, no driver has used a
fragment list containing more than a single fragment. Simplify the
NVO core and the drivers that use it by removing the whole concept of
the fragment list, and using a simple (address,length) pair instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Driver for Intel 82576 based virtual functions, based on Intel source
code available at:
http://sourceforge.net/projects/e1000 (igbvf-1.0.7)
Based on initial port from Eric Keller <ekeller@princeton.edu>.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Changes were made to files where the licence text within the files
themselves confirms that the files are GPL version 2 or later.
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Pass the settings block name as a parameter to register_settings(),
rather than defining it with settings_init() (and then possibly
changing it by directly manipulating settings->name).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
FCoE requires us to be able to receive unicast packets for multiple
addresses. Support this by operating in promiscuous mode.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
An attempt to transmit a packet of 8192 bytes or larger will collide
with the status bits in the TX descriptor. This gives the appearance
of the network card's transmit data path having just suddenly stopped
responding; iPXE is waiting for the card to report a TX completion
but, because of the status bit collision, the card thinks that the
descriptor has not yet been written.
Fix by explicitly checking for oversized packets in rtl_transmit().
Discovered during Fibre Channel over Ethernet testing, and debugged by
using gdb to examine the state of the emulated rtl8139 card in qemu.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the explicit calls from the Infiniband core to the IPoIB layer
with the general concept of an Infiniband upper-layer driver
(analogous to a PCI driver) which can create arbitrary devices on top
of Infiniband devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The rtl8139 driver includes the Ethernet CRC within the received
packet. All current protocols ignore trailing garbage, but FCoE
requires the frame length to be correct (since the FCoE footer
position is calculated from the end of the packet), so fix the driver
to strip out the CRC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add PCI ID 8086:27dc to the eepro100 driver.
Reported-by: Cédric Delmas <c.delmas@akka.eu>
Signed-off-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
alloc_memblock() and free_memblock() are internal.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
pcbios specific get_memmap() is used by the b44 driver making
all-drivers builds fail on other platforms. Move it to the I/O API
group and provide a dummy implementation on EFI.
Signed-off-by: Piotr Jaroszyński <p.jaroszynski@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch adds a native iPXE forcedeth driver and removes the legacy
Etherboot forcedeth driver. It supports 40 different chips, compared
to the original 14.
It has been tested on a NIC with an CK804 Ethernet Controller, and the
results of downloading 5 100mb images in a row have been:
12/11/11/11/11 seconds; booting DSL using pxelinux also succeeded. The
driver has also been tested by chaining undionly.kpxe and it worked.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Tested-by: Andrei Faur <da3drus@gmail.com>
Tested-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch adds a native iPXE virtio-net driver and removes the legacy
Etherboot virtio-net driver. The main reasons for doing this are:
1. Multiple virtio-net NICs are now supported by iPXE. The legacy
driver kept global state and caused issues in virtual machines with
more than one virtio-net device.
2. Faster downloads. The native iPXE driver downloads 100 MB over
HTTP in 12s, the legacy Etherboot driver in 37s. This simple
benchmark uses KVM with tap networking and the Python
SimpleHTTPServer both running on the same host.
Changes to core virtio code reduce vring descriptors to 256 (QEMU uses
128 for virtio-blk and 256 for virtio-net) and change the opaque token
from u16 to void*. Lowering the descriptor count reduces memory
consumption. The void* opaque token change makes driver code simpler.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This bug caused .probe to fail because the NIC did not reset properly.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add NonVolatile Option (nvo) and NonVolatile Storage (nvs) support to
the myri10ge driver using the EEPROM read/write mechanism provided by
the NIC's Vendor Specific PCI capability.
The myri10ge NIC is capabile of storing 64KB or more of nonvolatile
options, but this patch advertises only 512 bytes of nvo storage
because iPXE malloc's a buffer matching the total size we advertise.
512 is plenty without wasting malloc'd memory. (The 2 other drivers
currently supporting nvo advertise 256 bytes or less.)
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This patch removes the cfg lookup made in the r8169 driver and
replaces it with equivalent information found in the driver_data field
of the pci_device_id structure.
Signed-off-by: Andrei Faur <da3drus@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Michael Brown