The iBFT has a VLAN field that should be filled in. Add the
vlan_tag() function to extract the VLAN tag of a network device.
Since VLAN support is optional, define a weak function that returns 0
when iPXE is built without VLAN support.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid memory leaks by clearing any (non-child) settings immediately
before unregistering the network device settings block.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Including a netdev_poll() within net_tx() can cause the net_step()
loop to end up processing hundreds or thousands of packets within a
single step, since each received packet being processed may trigger a
response which, in turn causes a poll for further received packets.
Network devices must now ensure that the TX ring is at least as large
as the RX ring, in order to avoid running out of TX descriptors. This
should not cause any problems; unlike the RX ring, there is no
substantial memory cost incurred by increasing the TX ring size.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current logic is to process at most one received packet per call
to net_poll(), on the basis that refilling the hardware descriptor
ring should be delayed as little as possible. However, this limits
the rate at which packets can be processed and ultimately ends up
adding latency which, in turn, limits the achievable throughput.
With temporary modifications in place to essentially remove all
resource constraints (heap size increased to 16MB, RX descriptor ring
increased to 64 descriptors) and a TCP window size of 1MB, the
throughput on a gigabit (i.e. 119MBps) network can be observed to fall
off exponentially from around 115MBps to around 75MBps. Changing
net_poll() to process all received packets results in a steady
119MBps throughput.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Drivers are currently expected to initialise only the hardware
address, with the link-layer protocol code taking care of converting
this into a valid link-layer address. Some drivers (e.g. undinet) can
legitimately determine both the hardware and link-layer addresses,
which may differ.
Allow for this situation by checking to see if the link-layer address
is empty before initialising it from the hardware address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give the step() method a pointer to the containing object, rather than
a pointer to the process. This is consistent with the operation of
interface methods, and allows a single function to serve as both an
interface method and a process step() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow TX errors to be recorded against a network device even when the
packet didn't make it as far as netdev_tx().
Inspired-by: Dominik Russenberger <dominik.russenberger@terreactive.ch>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For devices that start in a link-down state, the user will see a
message such as:
[Link status: The socket is not connected (http://ipxe.org/38086001)]
Waiting for link-up on net0...
This is potentially misleading, since it suggests that there is a
genuine problem. Add a dedicated error message for "link down",
giving instead:
[Link status: Down (http://ipxe.org/38086101)]
Waiting for link-up on net0...
Reported-by: Tal Aloni <tal.aloni.il@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
netdev_close() assumes that devices that are open are on the
open_list, which wasn't true if device specific opening failed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Pass the settings block name as a parameter to register_settings(),
rather than defining it with settings_init() (and then possibly
changing it by directly manipulating settings->name).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Several use cases (e.g. the UNDI API and the EFI SNP API) require
access to the raw network device receive queue, and so currently use
manual calls to netdev_poll() on a specific network device in order to
prevent received packets from being processed by the network stack.
As an alternative, provide a flag that allows receive queue processing
to be frozen on a per-device basis. When receive queue processing is
frozen, packets will be enqueued as normal, but will not be
automatically dequeued and passed up the network stack.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Fix typographical error from commit ea631f6 ("[list] Add
list_first_entry()"). The symptom was PXELINUX 3.86 causing a stack
overflow under VMware.
Tested-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
There are several points in the iPXE codebase where
list_for_each_entry() is (ab)used to extract only the first entry from
a list. Add a macro list_first_entry() to make this code easier to
read.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
FCoE requires the use of fabric-provided MAC addresses, which breaks
the assumption that the net device's MAC address is implicitly the
source address for net_tx() and the (unicast) destination address for
net_rx().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Errors generated by the network layer in response to received packets
are liable to be lost, since nothing systematically records these
errors and often the packets do not propagate far enough through the
stack to impact upon user-visible processes.
Improve this situation by recording network-layer errors in the
network device statistics.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the concept of a network upper-layer driver, which can create
arbitrary devices on top of network devices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Setting NETDEV_DISCARD_RATE to a non-zero value will cause one in
every NETDEV_DISCARD_RATE packets to be discarded at random on both
the transmit and receive datapaths, allowing the robustness of
upper-layer network protocols to be tested even in simulation
environments that provide wholly reliable packet transmission.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Standardise on using ref_init() to initialise an embedded reference
count, to match the coding style used by other embedded objects.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
IPoIB has a 20-byte link-layer address, of which only eight bytes
represent anything relating to a "hardware address".
The PXE and EFI SNP APIs expect the permanent address to be the same
size as the link-layer address, so fill in the "permanent address"
field with the initial link layer address (as generated by
register_netdev() based upon the real hardware address).
The hardware address is an intrinsic property of the hardware, while
the link-layer address can be changed at runtime. This separation is
exposed via APIs such as PXE and EFI, but is currently elided by gPXE.
Expose the hardware and link-layer addresses as separate properties
within a net device. Drivers should now fill in hw_addr, which will
be used to initialise ll_addr at the time of calling
register_netdev().
The minimal-surprise behaviour, when no explicit SRP initiator device
is specified, will probably be to use the most recently opened
Infiniband device. This matches our behaviour with using the most
recently opened net device for PXE, iSCSI, AoE, NBI, etc.
Expand the NETDEV_LINK_UP bit into a link_rc status code field,
allowing specific reasons for link failure to be reported via
"ifstat".
Originally-authored-by: Joshua Oreman <oremanj@rwcr.net>
In order to construct outgoing link-layer frames or parse incoming
ones properly, some protocols (such as 802.11) need more state than is
available in the existing variables passed to the link-layer protocol
handlers. To remedy this, add struct net_device *netdev as the first
argument to each of these functions, so that more information can be
fetched from the link layer-private part of the network device.
Updated all three call sites (netdevice.c, efi_snp.c, pxe_undi.c) and
both implementations (ethernet.c, ipoib.c) of ll_protocol to use the
new argument.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
Intel's C compiler (icc) chokes on the zero-length arrays that we
currently use as part of the mechanism for accessing linker table
entries. Abstract away the zero-length arrays, to make a port to icc
easier.
Introduce macros such as for_each_table_entry() to simplify the common
case of iterating over all entries in a linker table.
Represent table names as #defined string constants rather than
unquoted literals; this avoids visual confusion between table names
and C variable or type names, and also allows us to force a
compilation error in the event of incorrect table names.
There are currently four places within the codebase that use a
heuristic to guess the "boot network device", with varying degrees of
success. Add a feature to the net device core to maintain a list of
open network devices, in order of opening, and provide a function
last_opened_netdev() to retrieve the most recently opened net device.
This should do a better job than the current assortment of
guess_boot_netdev() functions.
netdev_rx_err() and netdev_tx_complete_err() get passed the error
code, but currently use it only in debug messages.
Retain error numbers and frequencey counts for up to
NETDEV_MAX_UNIQUE_ERRORS (4) different errors for each of TX and RX.
This allows the "ifstat" command to report the reasons for TX/RX
errors in most cases, even in non-debug builds.
Settings can be constructed using a dotted-decimal notation, to allow
for access to unnamed settings. The default interpretation is as a
DHCP option number (with encapsulated options represented as
"<encapsulating option>.<encapsulated option>".
In several contexts (e.g. SMBIOS, Phantom CLP), it is useful to
interpret the dotted-decimal notation as referring to non-DHCP
options. In this case, it becomes necessary for these contexts to
ignore standard DHCP options, otherwise we end up trying to, for
example, retrieve the boot filename from SMBIOS.
Allow settings blocks to specify a "tag magic". When dotted-decimal
notation is used to construct a setting, the tag magic value of the
originating settings block will be ORed in to the tag number.
Store/fetch methods can then check for the magic number before
interpreting arbitrarily-numbered settings.
EFI requires us to be able to specify the source address for
individual transmitted packets, and to be able to extract the
destination address on received packets.
Take advantage of this to rationalise the push() and pull() methods so
that push() takes a (dest,source,proto) tuple and pull() returns a
(dest,source,proto) tuple.
Determine the network-layer packet type and fill it in for UNDI
clients. This is required by some NBPs such as emBoot's winBoot/i.
This change requires refactoring the link-layer portions of the
gPXE netdevice API, so that it becomes possible to strip the
link-layer header without passing the packet up the network stack.
Add a configuration settings block for each net device. This will
provide the parent scope for settings applicable only to that network
device (e.g. non-volatile options stored on the NIC, options obtained via
DHCP, etc.).
Expose the MAC address as a setting.
safe dropping of the netdev ref by the driver while other refs still
exist.
Add netdev_irq() method. Net device open()/close() methods should no
longer enable or disable IRQs.
Remove rx_quota; it wasn't used anywhere and added too much complexity
to implementing correct interrupt-masking behaviour in pxe_undi.c.
Stefan Hajnoczi