This commit adds an e1000e driver based on Intel source code
available at:
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support many PCIe e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This commit replaces the current gPXE e1000 driver with one ported
from Intel source code available at
http://sourceforge.net/projects/e1000/
which is upstream source for the Linux kernel e1000 drivers, and
should support most if not all PCI e1000 variants.
Signed-off-by: Marty Connor <mdc@etherboot.org>
The vxge driver code is split over several files, including vxge_main.c.
This causes the build system and ROM-o-matic to see the driver as
"vxge_main".
This patch adds a stub vxge.c which takes up no space but gives the
driver its proper name, "vxge".
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Align each ICM member alloc to the member size instead of page size.
Increase multicast table size to 128.
Signed-off-by: Itay Gazit <itaygazit@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The rtl818x driver uses programmed I/O but has a fallback to
memory-mapped I/O registers. The fallback currently will not work since
the registers are accessed using inl()/outl() programmed I/O functions
in the driver. This patch removes the fallback to we fail cleanly when
programmed I/O is not possible.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
This driver uses programmed I/O to access hardware registers. There is
a stray memory-mapped I/O read on a programmed I/O address. Perhaps
this is an artifact of porting the driver. Fix this by converting it to
programmed I/O.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
This seems to be necessary for some types of PCI devices. We had
problems when using gPXE in KVM virtual machines with direct
PCI device access.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Shao Miller <shao.miller@yrdsb.edu.on.ca>
Modified-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The previous [skge] commit should have been recorded as authored by
Thomas Miletich <thomas.miletich@gmail.com>
I mistakenly committed it improperly after fixing a merge issue.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This code is based on the linux skge driver. It supports Marvell Yukon
and SysKonnect Gigabit chipsets.
The code is based on code Michael Decker <mrd999@gmail.com> wrote for
Google Summer of Code 2008.
Support for dual-port cards is untested. The code, however, was left
in. In my opinion it's easier to fix the code if we need to, instead
of having to add support for it from scratch.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This driver supports all current Myricom 10 gigabit Ethernet NICs.
It was written from scratch for gPXE by Glenn Brown <glenn@myri.com>,
referenencing Myricom's Linux and EFI drivers, with permission.
Signed-off-by: Glenn Brown <glenn@myri.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
This version is Based on Michael Decker's GSoC 2008 code.
A number cleanups and fixes were applied.
Earlier-version-reviewed-by: Marty Connor <mdc@etherboot.org>
Earlier-version-tested-by: Marty Connor <mdc@etherboot.org>
Earlier-version-tested-by: Shao Miller <Shao.Miller@yrdsb.edu.on.ca>
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Reviewed-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The 82571 supports an alternate MAC address location in NVRAM.
When this is set, use this for the MAC rather than the default
physical MAC address.
Ported from linux-2.6.git 93ca161027eb6a1761fb674ad7b995aedccf5f6e
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The latest RTL-generated register lists include (mostly redundant)
xxx_MSB values alongside xxx_LSB and xxx_RMASK, and also include
default register values.
Some subnet managers expect the GetResponse from a SetPortInfo MAD to
contain the new link state. The transition is not immediate, so we
often end up returning the previous link state. This can cause the SM
to fail to activate the port.
Fix by waiting for up to 20us for the link state transition to take
effect.
The first byte of the IPoIB MAC address is used for flags indicating
support for "connected mode". Strip out the non-QPN bits of the first
dword when constructing the address vector for transmitted IPoIB
packets, so as not to end up passing an invalid QPN in the BTH.
Error message was:
[BUILD] bin/atl1e.oncc1: warnings being treated as errors
drivers/net/atl1e.c: In function 'atl1e_get_permanent_address':
drivers/net/atl1e.c:1326: error: dereferencing type-punned pointer will break strict-aliasing rules
make: *** [bin/atl1e.o] Error 1
Reported-by: Giandomenico De Tullio <ghisha@email.it>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
Modified-by: Michael Brown <mcb30@etherboot.org>
Remove spaces in 3rd PCI_ROM field.
Debugged-by: Marty Connor <mdc@etherboot.org>
Reported-by: Giandomenico De Tullio <ghisha@email.it>
Signed-off-by: Michael Brown <mcb30@etherboot.org>
The iBFT is Ethernet-centric in providing only six bytes for a MAC
address. This is most probably an indirect consequence of a similar
design flaw in the Windows NDIS stack. (The WinOF IPoIB stack
performs all sorts of contortions in order to pretend to the NDIS
layer that it is dealing with six-byte MAC addresses.)
There is no sensible way in which to extend the iBFT without breaking
compatibility with programs that expect to parse it. Add the notion
of an "Ethernet-compatible" MAC address to our link layer abstraction,
so that link layers can provide their own workarounds for this
limitation.
gcc 3.3.3 gave the following error when compiling sis190.c
drivers/net/sis190.c: In function 'sis190_get_mac_addr_from_apc':
drivers/net/sis190.c:966: warning: 'isa_bridge' might be used
uninitialized in this function
make: *** [bin/sis190.o] Error 1
This patch allows error-free compilation.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Some BIOSes set the PCI cacheline size to zero for the card; the ath5k
driver fixes it to a reasonable in PCI config space, but failed to
correct the internal value it had already read. This resulted in
divide-by-zero errors when cacheline-aligning various data structures.
Fix by setting the internal cachelsz to a sane value at the same time
as we write that value to PCI config space.
Signed-off-by: Marty Connor <mdc@etherboot.org>
This adds basic rfkill support for enabling the wireless card on certain
laptops, and changes miscellaneous other details that may help in obscure
cases.
Also change the error handling to not report CRC errors, which due to the
basic facts of wireless may happen even more frequently than valid packets.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Add the 82576 to the e1000 driver.
- Examining the Linux 2.6.30-rc4 igb driver, which supports this card and;
- Information available in the Intel® 82576 Gigabit Ethernet
Controller Datasheet v2.1, which is available from Intel's web site.
I only have a dual-ported card with Copper PHY, so any code paths relating
to Fibre haven't been tested. Also, I have only tested using auto-negotiation
of speed and duplex, and no flow control. Other code paths relating to
those settings also have not been exercised.
Signed-off-by: Simon Horman <horms@verge.net.au>
Sponsored-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Thomas Miletich <thomas.miletich@gmail.com>
Modified-by: Marty Connor <mdc@etherboot.org>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Enable interrupts in sis900_irq(). Doing so allows some programs using
gPXE's UNDI interface to work properly, including Symantec Ghost.
Tested-by: Hubert Mercier <hubert.mercier@unilim.fr>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Both methods disabled packet tx and rx just to have it enabled again
by calling a3c90x_reset().
Fixed by disabling tx and rx after the call to a3c90x_reset().
Tested by booting Ubuntu intrepid(8.10) directly from gPXE and pxelinux.
Tested on 3c905, 3c905B, 3c905C.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Some systems will retry their boot sequence in the event of a boot
failure. On these systems, the second and subsequent boot attempts
will fail to initialise the Hermon HCA.
Fix by resetting the HCA during probe(). This incurs a one-second
cost, but there seems to be no viable alternative.
Originally-fixed-by: Itay Gazit <itaygazit@gmail.com>
Some devices can only be reset via a mechanism that also resets the
card's PCI core, thus necessitating a backup and restore of all or
part of the PCI configuration space across a reset.
IPoIB has a 20-byte link-layer address, of which only eight bytes
represent anything relating to a "hardware address".
The PXE and EFI SNP APIs expect the permanent address to be the same
size as the link-layer address, so fill in the "permanent address"
field with the initial link layer address (as generated by
register_netdev() based upon the real hardware address).
The hardware address is an intrinsic property of the hardware, while
the link-layer address can be changed at runtime. This separation is
exposed via APIs such as PXE and EFI, but is currently elided by gPXE.
Expose the hardware and link-layer addresses as separate properties
within a net device. Drivers should now fill in hw_addr, which will
be used to initialise ll_addr at the time of calling
register_netdev().
With iSCSI, connection attempts are expensive; it may take many
seconds to determine that a connection will fail. SRP connection
attempts are much less expensive, so we may as well avoid the
"optimisation" of declaring a state of permanent failure after a
certain number of attempts. This allows a gPXE SRP initiator to
resume operations after an arbitrary amount of SRP target downtime.
SRP is the SCSI RDMA Protocol. It allows for a method of SAN booting
whereby the target is responsible for reading and writing data using
Remote DMA directly to the initiator's memory. The software initiator
merely sends and receives SCSI commands; it never has to touch the
actual data.
The ACK timeout determines how long we take to notice a failed
Reliable Connection. Reducing it from the arbitrary value of 19 down
to 14 reduces the individual ACK timeout from around 2.1s to 67ms;
this in turn reduces the time to tear down and re-establish a broken
SRP session from around 30s to around 1s.
The Infiniband Communication Manager will refuse to establish a
connection if it believes the connection is already established.
There is no immediately obvious way to ask it to tear down the
existing connection and replace it; to issue a DREP we would need to
know the local and remote communication IDs used for the previous
connection setup.
We can work around this by randomising the high-order bits of the
queue pair number; these have no significance to the hardware, but are
sufficient to convince the IB CM that this is a different connection.
The prior net80211 model of physical-layer behavior for drivers was
overly simplistic and limited the drivers that could be written. To
be more flexible, split the driver-provided list of supported rates by
band, and add a means for specifying a list of supported channels.
Allow drivers to specify a hardware channel value that will be tied to
uses of the channel.
Expose net80211_duration() to drivers, and make the rate it uses in
its computations configurable, so that it can be used in calculating
durations that must be set in hardware for ACK and CTS packets. Add
net80211_cts_duration() for the common case of calculating the
duration for a CTS packet.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
The IBA specification refers to management "interfaces" and "agents".
The interface is the component that connects to the queue pair and
sends and receives MADs; the agent is the component that constructs
the reply to the MAD.
Rename the IB_{QPN,QKEY,QPT} constants as a first step towards making
this separation in gPXE.
The Linux IB Communication Manager will always send MADs to QP1,
rather than back to the originating QP. On Hermon, QP1 is by default
handled by the embedded firmware. We can change this, but the cost is
that we have to handle both QP0 and QP1 (i.e. we have to provide SMA
as well as GMA service in software), and we have to use MLX queues
rather than standard UD queues (i.e. we have to construct the UD
datagrams by hand).
There doesn't seem to be any viable way around this situation, ugly
though it is.
Queue pairs are now assumed to be created in the INIT state, with a
call to ib_modify_qp() required to bring the queue pair to the RTS
state.
ib_modify_qp() no longer takes a modification list; callers should
modify the relevant queue pair parameters (e.g. qkey) directly and
then call ib_modify_qp() to synchronise the changes to the hardware.
The packet sequence number is now a property of the queue pair, rather
than of the device.
Each queue pair may have an associated address vector. For RC queue
pairs, this is the address vector that will be programmed in to the
hardware as the remote address. For UD queue pairs, it will be used
as the default address vector if none is supplied to ib_post_send().
The queue key is stored as a property of the queue pair, and so can
optionally be added by the Infiniband core at the time of calling
ib_post_send(), rather than always having to be specified by the
caller.
This allows IPoIB to avoid explicitly keeping track of the data queue
key.
Now that path record lookups are handled entirely via
ib_resolve_path(), the only role of the IPoIB peer cache is as a
lookup table for MAC addresses. Update the code structure and
comments to reflect this.
The IPoIB broadcast MAC address varies according to the partition key.
Now that the broadcast MAC address is a property of the network device
rather than of the link layer, we can expose this real MAC address
directly.
The broadcast LID is now identified via a path record lookup; this is
marginally inefficient (since it was present in the MCMemberRecord
GetResponse), but avoids the need to special-case broadcasts when
constructing the address vector in ipoib_transmit().
Currently, all Infiniband users must create a process for polling
their completion queues (or rely on a regular hook such as
netdev_poll() in ipoib.c).
Move instead to a model whereby the Infiniband core maintains a single
process calling ib_poll_eq(), and polling the event queue triggers
polls of the applicable completion queues. (At present, the
Infiniband core simply polls all of the device's completion queues.)
Polling a completion queue will now implicitly refill all attached
receive work queues; this is analogous to the way that netdev_poll()
implicitly refills the RX ring.
Infiniband users no longer need to create a process just to poll their
completion queues and refill their receive rings.
IPoIB and the SMA have separate constants for the packet size to be
used to I/O buffer allocations. Merge these into the single
IB_MAX_PAYLOAD_SIZE constant.
(Various other points in the Infiniband stack have hard-coded
assumptions of a 2048-byte payload; we don't currently support
variable MTUs.)
IPoIB has a link-layer broadcast address that varies according to the
partition key. We currently go through several contortions to pretend
that the link-layer address is a fixed constant; by making the
broadcast address a property of the network device rather than the
link-layer protocol it will be possible to simplify IPoIB's broadcast
handling.
Move the icky call to step() from aoe.c to ata.c; this takes it at
least one step further away from where it really doesn't belong.
Unfortunately, AoE has the ugly aoe_discover() mechanism which means
that we still have a step() loop in aoe.c for now; this needs to be
replaced at some future point.
In order to construct outgoing link-layer frames or parse incoming
ones properly, some protocols (such as 802.11) need more state than is
available in the existing variables passed to the link-layer protocol
handlers. To remedy this, add struct net_device *netdev as the first
argument to each of these functions, so that more information can be
fetched from the link layer-private part of the network device.
Updated all three call sites (netdevice.c, efi_snp.c, pxe_undi.c) and
both implementations (ethernet.c, ipoib.c) of ll_protocol to use the
new argument.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
Several SPI chips will respond to an SPI read command with a dummy
zero bit immediately prior to the first real data bit. This can be
used to autodetect the address length, provided that the command
length and data length are already known, and that the MISO data line
is tied high.
Tested-by: Thomas Miletich <thomas.miletich@gmail.com>
Debugged-by: Thomas Miletich <thomas.miletich@gmail.com>
The pcnet32 driver mismanages its RX buffers, with the result that
packets get corrupted if more than one packet arrives between calls to
poll().
Originally-fixed-by: Bill Lortz <Bill.Lortz@premier.org>
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Tested-by: Stefan Hajnoczi <stefanha@gmail.com>
Also adds the MAC_ADDR_CORRECT flag, to indicate whether or not the
MAC address needs to be fixed up by the driver.
Signed-off-by: Michael Brown <mcb30@etherboot.org>
This is a major rewrite of the legacy etherboot 3c90x driver using the
gPXE API for much improved performance over the legacy driver it
replaces.
This driver has been tested on 3c905, 3c905B, and 3c905C cards.
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Reviewed-by: Marty Connor <mdc@etherboot.org>
Tested-by: Marty Connor <mdc@etherboot.org>
Tested-by: Daniel Verkamp <daniel@drv.nu>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Intel's C compiler (icc) chokes on the zero-length arrays that we
currently use as part of the mechanism for accessing linker table
entries. Abstract away the zero-length arrays, to make a port to icc
easier.
Introduce macros such as for_each_table_entry() to simplify the common
case of iterating over all entries in a linker table.
Represent table names as #defined string constants rather than
unquoted literals; this avoids visual confusion between table names
and C variable or type names, and also allows us to force a
compilation error in the event of incorrect table names.
