http_step() allocates a potentially large block of storage (since the
URI can be arbitrarily long), and can be invoked as part of an already
deep call stack via xfer_window_changed().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow TFTP to be configured out by moving the next-server setting
definition (which is used by autoboot.c) from tftp.c to settings.c.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
sizeof(cipherspec) is obviously wrong in this context, because it will
only zero the first 4 or 8 bytes (cipherspec is a pointer).
This problem was reported by cppcheck.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use a private ANSI escape sequence to convey the priority of an
internal syslog() message through to the syslog server.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
An ANSI escape sequence context cannot be shared between multiple
users. Make the ANSI escape sequence context part of the line console
definition and provide individual contexts for each user.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The output from text-based user interfaces such as the "config"
command is not generally meaningful for logfile-based consoles such as
syslog and vmconsole.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the concept of a "console usage", such as "standard output" or
"debug messages". Allow usages to be associated with each console
independently. For example, to send debugging output via the serial
port, while preventing it from appearing on the local console:
#define CONSOLE_SERIAL CONSOLE_USAGE_ALL
#define CONSOLE_PCBIOS ( CONSOLE_USAGE_ALL & ~CONSOLE_USAGE_DEBUG )
If no usages are explicitly specified, then a default set of usages
will be applied. For example:
#define CONSOLE_SERIAL
will have the same affect as
#define CONSOLE_SERIAL CONSOLE_USAGE_ALL
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Simplify code by recording the active handshake digest algorithm as a
session parameter. (Note that we must still accumulate digests for
all supported algorithms, since we don't know which digest will
eventually be used until we receive the Server Hello.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
TLSv1.1 and earlier use a hybrid of MD5 and SHA-1 to generate digests
over the handshake messages. Formalise this as a separate digest
algorithm "md5+sha1".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Validate the server certificate against the trusted root certificate
store. The server must provide a complete certificate chain, up to
and including the trusted root certificate that is embedded into iPXE.
Note that the date and time are not yet validated.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
All axTLS files are now vanilla versions of the upstream axTLS files,
with one minor exception: the unused "ctx" parameter of
bi_int_divide() has been marked with "__unused" to avoid a compilation
error.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Advertise support for TLS version 1.1, and be prepared to downgrade to
TLS version 1.0. Tested against Apache with mod_gnutls, using the
GnuTLSPriorities directive to force specific protocol versions.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow packet transmission to be deferred pending successful ARP
resolution. This avoids the time spent waiting for a higher-level
protocol (e.g. TCP or TFTP) to attempt retransmission.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some PXE stacks (observed with a QLogic 8242) will always try to
prepend a link-layer header, even if the caller uses P_UNKNOWN to
indicate that the link-layer header has already been filled in. This
results in an invalid packet being transmitted.
Work around these faulty PXE stacks where possible by stripping the
existing link-layer header and allowing the PXE stack to (re)construct
the link-layer header itself.
Originally-fixed-by: Buck Huppmann <buckh@pobox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some iSCSI targets respond to a PDU before receiving the padding
bytes. If the target responds quickly enough, this can cause iPXE to
start processing a new TX PDU before the padding bytes have been sent,
which results in a protocol violation.
Fix by always transmitting the padding bytes along with the data
segment.
Originally-fixed-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As RFC 2616 10.3.4 explains, a 303 status is the proper HTTP 1.1
behavior for what most HTTP 1.0 clients did with code 302.
Signed-off-by: Jason Lunz <lunz@acm.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Abstract out the generic line-handling portions of the syslog
putchar() routine, to allow use by other console types.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Explicitly disable the syslog console when no syslog server is
defined, rather than (ab)using the socket family address as an
equivalent console-enabled flag.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Separate out the core HTTP functionality (which is shared by both HTTP
and HTTPS) from the provision of the "http://" URI opener. This
allows for builds that support only "https://" URIs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The PXE specification requires us to request DHCP options 128 to 135
inclusive, although these have no defined purpose.
Suggested-by: Ralf Buettner <rab@bootix.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some iSCSI targets (observed with stgt) can be configured to reject
connections that do not use header or data digests, and will respond
with "HeaderDigest=Reject" and/or "DataDigest=Reject", while still
allowing the connection to proceed to the full feature phase.
According to a strict reading of RFC3720, we are perfectly safe to
ignore these "Reject" messages: upon such a rejection "the negotiated
key is left at its current value (or default if no value was set)".
Since the default value for both HeaderDigest and DataDigest is
"None", then the only viable conclusion to be drawn is that the value
resulting from "Reject" is still "None".
Unfortunately, stgt doesn't seem to agree with this interpretation of
events, causing us to eventually report an unhelpful "connection timed
out" message to the user when we don't get any response to our first
PDU in full feature phase.
Fix by detecting any rejected parameters and immediately reporting an
error, which at least gives the user some insight as to what the real
problem may be.
Reported-by: Michal Suchanek <hramrach@centrum.cz>
Tested-by: Michal Suchanek <hramrach@centrum.cz>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
