Unlike Arbel, port parameters must be applied via a separate call to
SET_PORT, rather than as parameters to INIT_PORT.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Only port state change events are currently mapped to our event queue,
since those are the only events we are prepared to handle. This
ignores a potentially useful source of diagnostic information in the
case of unexpected failures.
Fix by mapping all events to the event queue; a build with debugging
enabled will therefore at least dump the raw content of the unexpected
events.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Doorbell records are currently embedded within the completion queue
and receive work queue strucures, which are allocated using zalloc()
and so have an alignment guarantee of only sizeof(void*), i.e. four
bytes. This is sufficient for the receive work queue, but not for the
completion queue, which requires an alignment guarantee of eight
bytes.
Though not guaranteed, it so happens that zalloc() will always return
a pointer that is exactly four bytes above a sixteen-byte boundary.
The completion queue doorbell record is therefore always misaligned,
and the value passed to the hardware via SW2HW_CQ is actually always
pointing to the page_offset value within the MTT descriptor (which
directly precedes the inline doorbell record). Provided that the page
offset is greater than 0x100, this looks to the hardware like an
update_ci value of greater than 0x010000 (taking into account
endianness differences), and so the hardware will happily deliver more
than 0x010000 completions before stopping. Hence this problem is
rarely observable.
Fix by allocating the doorbell records separately and using the
correct alignment constraints.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Improve the utility of debugging messages by including the relevant
port number, queue number (QPN, CQN, EQN), work queue entry (WQE)
number, and physical addresses wherever applicable.
Add hermon_dump_cqctx() for dumping a completion queue context, and
hermon_fill_nop_send_wqe() for inserting NOPs into send work queues.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some systems will retry their boot sequence in the event of a boot
failure. On these systems, the second and subsequent boot attempts
will fail to initialise the Hermon HCA.
Fix by resetting the HCA during probe(). This incurs a one-second
cost, but there seems to be no viable alternative.
Originally-fixed-by: Itay Gazit <itaygazit@gmail.com>
The Infiniband Communication Manager will refuse to establish a
connection if it believes the connection is already established.
There is no immediately obvious way to ask it to tear down the
existing connection and replace it; to issue a DREP we would need to
know the local and remote communication IDs used for the previous
connection setup.
We can work around this by randomising the high-order bits of the
queue pair number; these have no significance to the hardware, but are
sufficient to convince the IB CM that this is a different connection.
The Linux IB Communication Manager will always send MADs to QP1,
rather than back to the originating QP. On Hermon, QP1 is by default
handled by the embedded firmware. We can change this, but the cost is
that we have to handle both QP0 and QP1 (i.e. we have to provide SMA
as well as GMA service in software), and we have to use MLX queues
rather than standard UD queues (i.e. we have to construct the UD
datagrams by hand).
There doesn't seem to be any viable way around this situation, ugly
though it is.
Infiniband devices no longer block waiting for link-up in
register_ibdev().
Hermon driver needs to create an event queue and poll for link-up events.
Infiniband core needs to reread MAD parameters when link state changes.
IPoIB needs to cope with Infiniband link parameters being only partially
available at probe and open time.
Arbel and Hermon cards both have multiple ports. Add the
infrastructure required to register each port as a separate IB
device. Don't yet register more than one port, since registration
will currently fail unless a valid link is detected.
Use ib_*_{set,get}_{drv,owner}data wrappers to access driver- and
owner-private data on Infiniband structures.
