At least one NII implementation (in a Microsoft Surface tablet) seems
to fail to report the absence (sic) of TX completions properly. Work
around this by checking for TX completions only when we expect to see
one.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some NII implementations will fail the GET_STATUS operation if we
request the media status. Fix by doing so only if GET_INIT_INFO
reported that media status is supported.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
In theory USB3 ports do not require a reset to enable the port.
Experimentation shows that this is sometimes required, particularly
when rerouting ports from EHCI to xHCI and switching speeds.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
xHCI provides a somewhat convoluted mechanism for specifying details
of a transaction translator. Hubs must be marked as such in the
device slot context. The only opportunity to do so is as part of a
Configure Endpoint command, which can be executed only when opening
the hub's interrupt endpoint.
We add a mechanism for host controllers to intercept the opening of
hub devices, providing xHCI with an opportunity to update the internal
device slot structure for the corresponding USB device to indicate
that the device is a hub. We then include the hub-specific details in
the input context whenever any Configure Endpoint command is issued.
When a device is opened, we record the device slot and port for its
transaction translator (if any), and supply these as part of the
Address Device command.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Support low-speed and full-speed devices attached to a USB2 hub. Such
devices use a transaction translator (TT) within the USB2 hub, which
asynchronously initiates transactions on the lower-speed bus and
returns the result via a split completion on the high-speed bus.
We make the simplifying assumption that there will never be more than
sixteen active interrupt endpoints behind a single transaction
translator; this assumption allows us to schedule all periodic start
splits in microframe 0 and all periodic split completions in
microframes 2 and 3. (We do not handle isochronous endpoints.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current endpoint reset logic defers the reset until the caller
attempts to enqueue a new transfer to that endpoint. This is
insufficient when dealing with endpoints behind a transaction
translator, since the transaction translator is a resource shared
between multiple endpoints.
We cannot reset the endpoint as part of the completion handling, since
that would introduce recursive calls to usb_poll(). Instead, we
add the endpoint to a list of halted endpoints, and perform the reset
on the next call to usb_step().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The endpoint may already have enqueued TRBs at the time that
xhci_endpoint_reset() is called. Ring the doorbell to resume
processing these TRBs immediately, rather than waiting until the next
call to xhci_endpoint_message() or xhci_endpoint_stream().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Several of the USB timeouts were chosen on the principle of "pick an
arbitrary but ridiculously large value, just to be safe". It turns
out that some of the timeouts permitted by the USB specification are
even larger: for example, control transactions are allowed to take up
to five seconds to complete.
Fix up these USB timeout values to match those found in the USB2
specification.
Debugged-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
xHCI (and EHCI) nominally provide a mechanism for releasing ownership
of the host controller back to the BIOS, which can then potentially
restore legacy USB keyboard functionality.
This is a rarely used code path, since most operating systems claim
ownership and never attempt to later return to the BIOS. On some
systems (observed with a Lenovo X1 Carbon), this code path leads to
obscure and interesting bugs: if the xHCI and EHCI controllers are
both claimed and later released back to the BIOS, then a subsequent
call to INT 16,0305 to set the keyboard repeat rate to a non-default
value will lock the system.
Obscure though this sequence of operations may sound, it is exactly
what happens when using iPXE to boot a Linux kernel via a USB network
card. There is old and probably unwanted code in Linux's
arch/x86/boot/main.c which sets the keyboard repeat rate (with the
accompanying comment "Set keyboard repeat rate (why?)"). When booting
Linux via a USB network card on a Lenovo X1 Carbon, the system
therefore locks up immediately after jumping to the kernel's entry
point.
Work around this problem by preventing the release of ownership back
to the BIOS if it is known that we are shutting down to boot an OS.
This should allow legacy USB keyboard functionality to be restored if
the user chooses to exit iPXE, while avoiding the rarely used code
paths (and corresponding BIOS bugs) if the user chooses instead to
boot an OS.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If the BIOS fails to gracefully release ownership of the xHCI
controller, we can forcibly claim it by disabling all SMIs via the
USB legacy support control/status register.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
RX FIFO overflow is almost inevitable since the (usable) USB2 bus
bandwidth is approximately one quarter of the Ethernet bandwidth.
Avoid flooding the console with RX FIFO overflow messages in a
standard debug build.
With TCP SACK implemented, the RX FIFO overflow no longer causes a
catastrophic drop in throughput. Experimentation shows that HTTP
downloads now progress at a fairly smooth 250Mbps, which is around the
maximum speed attainable for a USB2 NIC.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
This driver is functional but any downloads via a TCP-based protocol
tend to perform poorly. The 1Gbps Ethernet line rate is substantially
higher than the 480Mbps (in practice around 280Mbps) provided by USB2,
and the device has only 32kB of internal buffer memory. Our 256kB TCP
receive window therefore rapidly overflows the RX FIFO, leading to
multiple dropped packets (usually within the same TCP window) and
hence a low overall throughput.
Reducing the TCP window size so that the RX FIFO does not overflow
greatly increases throughput, but is not a general-purpose solution.
Further investigation is required to determine how other OSes
(e.g. Linux) cope with this scenario. It is possible that
implementing TCP SACK would provide some benefit.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Most devices expose at least the link up/down status via a bit in a
MAC register, since the MAC generally already needs to know whether or
not the link is up. Some devices (e.g. the SMSC75xx USB NIC) expose
this information to software only via the MII registers.
Provide a generic mii_check_link() implementation to check the BMSR
and report the link status via netdev_link_{up,down}().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE already sends RX notifications to the backend when needed, but
does not set the "feature-rx-notify" flag. As of XenServer 6.5, this
flag is mandatory and omitting it will cause the backend to fail.
Fix by setting the "feature-rx-notify" flag, to inform the backend
that we will send notifications.
Reported-by: Shalom Bhooshi <shalom.bhooshi@citrix.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Restore the original values of XUSB2PR and USB3PSSEN, in case we are
booting an OS with no support for xHCI.
Suggested-by: Dan Ellis <Dan.Ellis@displaylink.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Intel PCH controllers default to routing USB2 ports to EHCI rather
than xHCI, and default to disabling SuperSpeed connections.
Manipulate the PCI configuration space registers as necessary to
reroute ports and enable SuperSpeed.
Originally-fixed-by: Dan Ellis <Dan.Ellis@displaylink.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Relicense files with kind permission from
Stefan Hajnoczi <stefanha@redhat.com>
alongside the contributors who have already granted such relicensing
permission.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
At some point in the past few years, binutils became more aggressive
at removing unused symbols. To function as a symbol requirement, a
relocation record must now be in a section marked with @progbits and
must not be in a section which gets discarded during the link (either
via --gc-sections or via /DISCARD/).
Update REQUIRE_SYMBOL() to generate relocation records meeting these
criteria. To minimise the impact upon the final binary size, we use
existing symbols (specified via the REQUIRING_SYMBOL() macro) as the
relocation targets where possible. We use R_386_NONE or R_X86_64_NONE
relocation types to prevent any actual unwanted relocation taking
place. Where no suitable symbol exists for REQUIRING_SYMBOL() (such
as in config.c), the macro PROVIDE_REQUIRING_SYMBOL() can be used to
generate a one-byte-long symbol to act as the relocation target.
If there are versions of binutils for which this approach fails, then
the fallback will probably involve killing off REQUEST_SYMBOL(),
redefining REQUIRE_SYMBOL() to use the current definition of
REQUEST_SYMBOL(), and postprocessing the linked ELF file with
something along the lines of "nm -u | wc -l" to check that there are
no undefined symbols remaining.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
These files cannot be automatically relicensed by util/relicense.pl
since they either contain unusual but trivial contributions (such as
the addition of __nonnull function attributes), or contain lines
dating back to the initial git revision (and so require manual
knowledge of the code's origin).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Relicence files with kind permission from the following contributors:
Alex Williamson <alex.williamson@redhat.com>
Eduardo Habkost <ehabkost@redhat.com>
Greg Jednaszewski <jednaszewski@gmail.com>
H. Peter Anvin <hpa@zytor.com>
Marin Hannache <git@mareo.fr>
Robin Smidsrød <robin@smidsrod.no>
Shao Miller <sha0.miller@gmail.com>
Thomas Horsten <thomas@horsten.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add the standard warranty disclaimer and Free Software Foundation
address paragraphs to the licence text where these are not currently
present.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When a command times out, abort it (via the Command Abort bit in the
Command Ring Control Register) so that subsequent commands may execute
as expected.
This improves robustness when a device fails to respond to the Set
Address command, since the subsequent Disable Slot command will now
succeed.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If the Disable Slot command fails then the hardware may continue to
write to the slot context. Leak the memory used by the slot context
to avoid future memory corruption.
This situation has been observed in practice when a Set Address
command fails, causing the command ring to become temporarily
unresponsive.
Note that there is no need to similarly leak memory on the failure
path in xhci_device_open(), since in the event of a failure the
hardware is never informed of the slot context address.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a generic framework for allocating, refilling, and optionally
recycling I/O buffers used by bulk IN and interrupt endpoints.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit a60f2dd ("[usb] Try multiple USB device configurations")
changed the behaviour of register_usb() such that if no drivers are
found then the device will be closed and the memory used will be
freed.
If a port status change subsequently occurs while the device is still
physically attached, then usb_hotplug() will see this as a new device
having been attached, since there is no device recorded as being
currently attached to the port. This can lead to spurious hotplug
events (or even endless loops of hotplug events, if the process of
opening and closing the device happens to generate a port status
change).
Fix by using a separate flag to indicate that a device is physically
attached (even if we have no corresponding struct usb_device).
Reported-by: Dan Ellis <Dan.Ellis@displaylink.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some xHCI controllers (observed with a Renesas Electronics PCIe USB3
card) seem to require a delay after forcing the link state of USB3
ports to RxDetect. Omitting this delay causes strange behaviour
including system lockups.
Add an unconditional 20ms delay after writing the port link states.
This seems to be sufficient to avoid the problem.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
