Some iSCSI targets respond to a PDU before receiving the padding
bytes. If the target responds quickly enough, this can cause iPXE to
start processing a new TX PDU before the padding bytes have been sent,
which results in a protocol violation.
Fix by always transmitting the padding bytes along with the data
segment.
Originally-fixed-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As RFC 2616 10.3.4 explains, a 303 status is the proper HTTP 1.1
behavior for what most HTTP 1.0 clients did with code 302.
Signed-off-by: Jason Lunz <lunz@acm.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Separate out the core HTTP functionality (which is shared by both HTTP
and HTTPS) from the provision of the "http://" URI opener. This
allows for builds that support only "https://" URIs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some iSCSI targets (observed with stgt) can be configured to reject
connections that do not use header or data digests, and will respond
with "HeaderDigest=Reject" and/or "DataDigest=Reject", while still
allowing the connection to proceed to the full feature phase.
According to a strict reading of RFC3720, we are perfectly safe to
ignore these "Reject" messages: upon such a rejection "the negotiated
key is left at its current value (or default if no value was set)".
Since the default value for both HeaderDigest and DataDigest is
"None", then the only viable conclusion to be drawn is that the value
resulting from "Reject" is still "None".
Unfortunately, stgt doesn't seem to agree with this interpretation of
events, causing us to eventually report an unhelpful "connection timed
out" message to the user when we don't get any response to our first
PDU in full feature phase.
Fix by detecting any rejected parameters and immediately reporting an
error, which at least gives the user some insight as to what the real
problem may be.
Reported-by: Michal Suchanek <hramrach@centrum.cz>
Tested-by: Michal Suchanek <hramrach@centrum.cz>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
According to section 14.23 of RFC2616, an HTTP Host header without
port implies the default port is used. Thus, when fetching from
anywhere but port 80 for HTTP or 443 for HTTPS, the port ought to be
explicitly given in that header. Otherwise, some servers might fail
to associate the request with the correct virtual host or generate
incorrect self-referencing URLs.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The iSCSI TX process can now be woken up by the TCP socket via
xfer_window_changed(), so it is no longer valid to assume that
iscsi_tx_step() can be called in state ISCSI_TX_IDLE only immediately
after completing a transmission.
Fix by calling iscsi_tx_done() only upon a transition into state
ISCSI_TX_IDLE.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide support for HTTP range requests, and expose this functionality
via the iPXE block device API. This allows SAN booting from a root
path such as:
sanboot http://boot.ipxe.org/freedos/fdfullcd.iso
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Give the step() method a pointer to the containing object, rather than
a pointer to the process. This is consistent with the operation of
interface methods, and allows a single function to serve as both an
interface method and a process step() method.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
ftp_data_deliver() does nothing except pass through the received data
to the xfer interface, and so can be eliminated by using a
pass-through interface.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Booting from an HTTP SAN will require HTTP range requests, which are
defined only in HTTP/1.1 and above. HTTP/1.1 mandates support for
"Transfer-Encoding: chunked", so we must support it.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Improve the appearance of the "config" user interface by ensuring that
settings appear in some kind of logical order.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The default initiator IQN is "iqn.2000-09.org.etherboot:UNKNOWN".
This is problematic for two reasons:
a) the etherboot.org domain (and hence the associated IQN namespace)
is not under the control of the iPXE project, and
b) some targets (correctly) refuse to allow concurrent connections
from different initiators using the same initiator IQN.
Solve both problems by changing the default initiator IQN to be
iqn.2010-04.org.ipxe:<hostname> if a hostname is set, or
iqn.2010-04.org.ipxe:<uuid> if no hostname is set.
Explicit initiator IQNs set via DHCP option 203 are not affected by
this change.
Unfortunately, this change is likely to break some existing
configurations, where ACL rules have been put in place referring to
the old default initiator IQN. Users may need to update ACLs, or
force the use of the old IQN using an iPXE script line such as
set initiator-iqn iqn.2000-09.org.etherboot:UNKNOWN
or a dhcpd.conf option such as
option iscsi-initiator-iqn "iqn.2000-09.org.etherboot:UNKNOWN"
Signed-off-by: Michael Brown <mcb30@ipxe.org>
After a more accurate reading of RFC 3720, it becomes clear how NOPs
are supposed to work. The current implementation (which just ignores
NOP-Ins) is sufficient to cope with NOP-Ins sent to update CmdSN, but
will need to be extended before it can cope with NOP-Ins sent as iSCSI
keepalives.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some iSCSI targets (observed with a Synology DS207+ NAS) send
unsolicited NOP-Ins to the initiator. RFC 3720 is remarkably unclear
and possibly self-contradictory on how NOPs are supposed to work, but
it seems as though we can legitimately just ignore any unsolicited
NOP-In PDU.
Reported-by: Marc Lecuyer <marc@maxiscreen.com>
Originally-implemented-by: Thomas Miletich <thomas.miletich@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 5f4ab0d ("[iscsi] Randomise a portion of the ISID to force new
session instantiation") introduced a regression by randomising the
ISID on each call to iscsi_start_login(), which may be called more
than once per connection, rather than on each call to
iscsi_open_connection(), which is guaranteed to be called only once
per connection. This is incorrect behaviour that causes our
connection to be rejected by some iSCSI targets (observed with a
COMSTAR target under OpenSolaris).
Fix by generating the ISID in iscsi_open_connection(), and storing the
randomised ISID as part of the session state.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When a connection to an iSCSI target is broken without gracefully
closing the TCP socket, a subsequent connection attempt may fail
because the target believes that we are attempting session
reinstatement (see RFC3720 section 5.3.1). This has been observed
using the Microsoft iSCSI target.
Section 9.1.1 of RFC3720 states that initiators should use a stable
ISID, however section 5.3.1 shows that the only way to explicitly
request that a new session be created is to use a new ISID.
Fix by randomising the "qualifier" portion of the ISID.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The block device interface used in gPXE predates the invention of even
the old gPXE data-transfer interface, let alone the current iPXE
generic asynchronous interface mechanism. Bring this old code up to
date, with the following benefits:
o Block device commands can be cancelled by the requestor. The INT 13
layer uses this to provide a global timeout on all INT 13 calls,
with the result that an unexpected passive failure mode (such as
an iSCSI target ACKing the request but never sending a response)
will lead to a timeout that gets reported back to the INT 13 user,
rather than simply freezing the system.
o INT 13,00 (reset drive) is now able to reset the underlying block
device. INT 13 users, such as DOS, that use INT 13,00 as a method
for error recovery now have a chance of recovering.
o All block device commands are tagged, with a numerical tag that
will show up in debugging output and in packet captures; this will
allow easier interpretation of bug reports that include both
sources of information.
o The extremely ugly hacks used to generate the boot firmware tables
have been eradicated and replaced with a generic acpi_describe()
method (exploiting the ability of iPXE interfaces to pass through
methods to an underlying interface). The ACPI tables are now
built in a shared data block within .bss16, rather than each
requiring dedicated space in .data16.
o The architecture-independent concept of a SAN device has been
exposed to the iPXE core through the sanboot API, which provides
calls to hook, unhook, boot, and describe SAN devices. This
allows for much more flexible usage patterns (such as hooking an
empty SAN device and then running an OS installer via TFTP).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE has never supported SEEK_END; the usage of "whence" offers only
the options of SEEK_SET and SEEK_CUR and so is effectively a boolean
flag. Further flags will be required to support additional metadata
required by the Fibre Channel network model, so repurpose the "whence"
field as a generic "flags" field.
xfer_seek() has always been used with SEEK_SET, so remove the "whence"
field altogether from its argument list.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove data-xfer as an interface type, and replace data-xfer
interfaces with generic interfaces supporting the data-xfer methods.
Filter interfaces (as used by the TLS layer) are handled using the
generic pass-through interface capability. A side-effect of this is
that deliver_raw() no longer exists as a data-xfer method. (In
practice this doesn't lose any efficiency, since there are no
instances within the current codebase where xfer_deliver_raw() is used
to pass data to an interface supporting the deliver_raw() method.)
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Standardise on using ref_init() to initialise an embedded reference
count, to match the coding style used by other embedded objects.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 3d9dd93 introduced a regression in HTTP: if a URI without a
path is specified (e.g. http://netboot.me), we send the empty string
as our GET request. Reintroduce an extra slash when uri->path is NULL,
to turn this into the expected GET /.
Reported-by: Kyle Kienapfel <doctor.whom@gmail.com>
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
The default user and password are used for anonymous FTP by default.
This patch adds support for an explicit user name and password in an FTP
URI:
imgfetch ftp://user:password@server.com/path/to/file
Edited-by: Stefan Hajnoczi <stefanha@gmail.com>. Bugs are my fault.
Signed-off-by: Marty Connor <mdc@etherboot.org>
Currently, handling of URI escapes is ad-hoc; escaped strings are
stored as-is in the URI structure, and it is up to the individual
protocol to unescape as necessary. This is error-prone and expensive
in terms of code size. Modify this behavior by unescaping in
parse_uri() and escaping in unparse_uri() those fields that typically
handle URI escapes (hostname, user, password, path, query, fragment),
and allowing unparse_uri() to accept a subset of fields to print so
it can be easily used to generate e.g. the escaped HTTP path?query
request.
Signed-off-by: Joshua Oreman <oremanj@rwcr.net>
Signed-off-by: Marty Connor <mdc@etherboot.org>
Avoid passing credentials in the iBFT that were available but not
required for login. This works around a problem in the Microsoft
iSCSI initiator, which will refuse to initiate sessions if the CHAP
password is fewer than 12 characters, even if the target ends up not
asking for CHAP authentication.
The documentation in xfer.h and xfer.c does not say that the metadata
parameter is optional in calls such as xfer_deliver_iob_meta() and the
deliver_iob() method. However, some code in net/ is prepared to
accept a NULL pointer, and xfer_deliver_as_iob() passes a NULL pointer
directly to the deliver_iob() method.
Fix this mess of conflicting assumptions by making everything assume
that the metadata parameter is mandatory, and fixing
xfer_deliver_as_iob() to pass in a dummy metadata structure (as is
already done in xfer_deliver_iob()).
