Some xHCI controllers (such as qemu's emulated xHCI controller) do not
correctly handle zero-length packets that are part of a TRB chain.
The zero-length TRB ends up being squashed and does not result in a
zero-length packet as seen by the device.
Work around this problem by marking the zero-length packet as
belonging to a separate transfer descriptor.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some hubs (e.g. the Avocent Corp. Virtual Hub on a Lenovo x3550
Integrated Management Module) have been observed to require more than
the standard 200ms for ports to stabilise, with the result that
devices appear to disconnect and immediately reconnect during the
initial bus enumeration.
Work around this problem by allowing specific hubs an extra 500ms of
settling time.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Record the speed of a USB device based on the port's speed at the time
that the device was enabled. This allows us to remember the device's
speed even after the device has been disconnected (and so the port's
current speed has changed).
In particular, this allows us to correctly identify the transaction
translator for a low-speed or full-speed device after the device has
been disconnected.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The usb_message() and usb_stream() functions currently check for
port->speed==USB_SPEED_NONE to determine whether or not a device has
been unplugged. This test will give a false negative result if a new
device has been plugged in before the hotplug mechanism has finished
handling the removal of the old device.
Fix by checking instead the port->disconnected flag, which is now
cleared only after completing the removal of the old device.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide BIT_QWORD_PTR() to allow for easy extraction of non-endian
fields (e.g. Infiniband GUIDs) without unnecessary byte swapping.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Tested using QEMU and usbredir to expose the LAN9512 chip present on a
Raspberry Pi.
There is a known issue with the LAN9512: an extra two bytes are
appended to every transmitted packet. These two bytes comprise:
{ 0x00, 0x08 } if packet length == 0 (mod 8)
{ CRC[0], 0x00 } if packet length == 7 (mod 8)
{ CRC[0], CRC[1] } otherwise
The extra bytes are appended whether the Ethernet CRC is generated
manually or added automatically by the hardware. The issue occurs
with the Linux kernel driver as well as the iPXE driver. It appears
to be an undocumented hardware errata.
TCP/IP traffic is not affected, since the IP header length field
causes the extraneous bytes to be discarded by the receiver. However,
protocols that rely on the length of the Ethernet frame (such as FCoE
or iPXE's "lotest" protocol) will be unusable on this hardware.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
On some models (notably ICH), the PHY reset mechanism appears to be
broken. In particular, the PHY_CTRL register will be correctly loaded
from NVM but the values will not be propagated to the "OEM bits" PHY
register. This typically has the effect of dropping the link speed to
10Mbps.
Since the original version of this driver in commit 945e428 ("[intel]
Replace driver for Intel Gigabit NICs"), we have always worked around
this problem by skipping the PHY reset if the link is already up.
Enhance this workaround by explicitly checking for known-broken PCI
IDs.
Reported-by: Robin Smidsrød <robin@smidsrod.no>
Tested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE does not call shutdown() before invoking a COMBOOT executable,
since the executable is allowed to make API calls back into iPXE. If
a background picture is used, then the console will not be restored to
text mode before invoking the COMBOOT executable. This can cause
undefined behaviour.
Fix by adding an explicit call to console_reset() immediately before
invoking a COMBOOT or COM32 executable, analogous to the call made to
console_reset() immediately before invokving a PXE NBP.
Debugged-by: Andrew Widdersheim <awiddersheim@inetu.net>
Tested-by: Andrew Widdersheim <awiddersheim@inetu.net>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
For switches which remain permanently in the non-forwarding state (or
which erroneously report a non-forwarding state), ensure that iPXE
will eventually give up waiting for the link to become unblocked.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If we detect (via STP) that a switch port is in a non-forwarding
state, then the link is marked as being temporarily blocked and DHCP
discovery will be deferred until the link becomes unblocked.
The timer used to decide when to give up waiting for ProxyDHCPOFFERs
is currently based on the time that DHCP discovery was started, and
makes no allowances for any time spent waiting for the link to become
unblocked. Consequently, if STP is used then the timeout for
ProxyDHCPOFFERs becomes essentially zero.
Fix by resetting the recorded start time whenever DHCP discovery is
deferred due to a blocked link.
Debugged-by: Sebastian Roth <sebastian.roth@zoho.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The name "vesafb" is intrinsically specific to a BIOS environment.
Generalise the build configuration option CONSOLE_VESAFB to
CONSOLE_FRAMEBUFFER, in preparation for adding EFI framebuffer
support.
Existing configurations using CONSOLE_VESAFB will continue to work.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid accidentally dereferencing a NULL cipher context pointer for
plaintext blocks (which are usually messages with a block length of
zero, indicating a missing block).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
UEFI UNDI is a hideously ugly lump of poorly specified garbage bolted
on as an appendix of the UEFI specification. My personal favourite
line from the UNDI 'specification' is section E.2.2, which states
"Basically, the rule is: Do it right, or don't do it at all". The
author appears to believe that such exhortations are a viable
substitute for documenting what it is that the wretched reader is
supposed to, in fact, do.
(Second favourite is the section listing the pros and cons of various
driver types. This fails to identify a single con for the mythical
"Hardware UNDI", a design so insanely intrinsically slow that it
appears to have been the inspiration for the EFI_USB_IO_PROTOCOL.)
UNDI is functionally isomorphic to the substantially less preposterous
EFI_SIMPLE_NETWORK_PROTOCOL. Provide an UNDI interface (as a thin
wrapper around the existing SNP interface) to allow for use by
third-party software that has made poor life choices.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Calling EDK2's OpenProtocol() with attributes BY_DRIVER|EXCLUSIVE will
call DisconnectController() in a loop to attempt to dislodge any
existing openers with attributes BY_DRIVER. The loop will continue
indefinitely until either no such openers remain, or until
DisconnectController() returns an error.
If our driver binding protocol's Stop() method is ever called to
disconnect a device that we are not in fact driving, then return
EFI_DEVICE_ERROR rather than EFI_SUCCESS, in order to break this
potentially infinite loop.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Microsoft PE/COFF specification defines the MajorLinkerVersion and
MinorLinkerVersion fields as "The linker major version number" and
"The linker minor version number" respectively, and has nothing more
to say on the matter. These fields have no significance: they do not
affect the interpretation of the remainder of the file, but merely
provide diagnostic information for interested humans to read.
Apparently, versions 2.4 and earlier of the Microsoft linker produced
binaries so incorrigibly cursed that even to attempt to parse such a
binary would risk summoning a plague of enraged spiders. To protect
users from unwanted arachnids, ImageHlp.dll's MapAndLoad() function
will helpfully fail to map and/or load a 32-bit binary unless the
linker version field indicates version 2.5 or later. (64-bit binaries
are exempt from such helpfulness.)
Work around the broken Microsoft ImageHlp.dll library by providing a
linker version number that will satisfy the arbitrary whims of the
MapAndLoad() function.
This mirrors wimboot commit 670c7e2 ("[efi] Work around broken 32-bit
PE executable parsing in ImageHlp.dll").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Use INT 1a,564e to notify the BIOS of each network device that we
detect. This provides an opportunity for the BIOS to implement
platform policy such as changing the MAC address by issuing a call to
PXENV_UNDI_SET_STATION_ADDRESS.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Invoke INT 1a,564e whenever a PXE stack is activated, passing the
address of the PXENV+ structure in %es:%bx. This is designed to allow
a BIOS to be notified when a PXE stack has been installed, providing
an opportunity for start-of-day commands such as setting the MAC
address according to a policy chosen by the BIOS.
PXE defines INT 1a,5650 as a means of locating the PXENV+ structure:
this call returns %ax=0x564e and the address of the PXENV+ structure
in %es:%bx. We choose INT 1a,564e as a fairly natural notification
call, using the parameters as would be returned by INT 1a,5650.
The full calling convention (documented as per section 3.1 of the PXE
specification) is:
INT 1a,564e - PXE installation notification
Enter:
%ax = 0x564e
%es = 16-bit segment address of the PXENV+ structure
%bx = 16-bit offset of the PXENV+ structure
Exit:
%edx may be trashed (as is the case for INT 1a,5650)
All other register contents must be preserved
CF is cleared
IF is preserved
All other flags are undefined
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid dragging in unnecessary iPXE header files such as <ipxe/uuid.h>
and <ipxe/tables.h> when building host utilities, and ensure that
FILE_LICENCE() (present in the imported EDK2 headers) expands to a
no-op.
Reported-by: Michael Tautschnig <mt@debian.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 7d36a1b ("[build] Explicitly link efilink against -liberty")
introduced a dependency on libiberty to cope with old versions of
libbfd. This commit dates from 2008 and seems to apply only to what
are now extremely old versions of libbfd (prior to binutils 2.12).
There are systems (such as current Debian) which do not include
libiberty within the binutils packages. On such systems, our build
dependency on libiberty represents a pointless hurdle.
Remove the explicit dependency on libiberty, hoping that there are no
modern systems where this will cause a problem.
Suggested-by: Ben Hildred <42656e@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the UEFI platform firmware to provide drivers for unrecognised
devices, by exposing our own implementation of EFI_USB_IO_PROTOCOL.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Make the class ID a property of the USB driver (rather than a property
of the USB device ID), and allow USB drivers to specify a wildcard ID
for any of the three component IDs (class, subclass, or protocol).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generate a score for each possible USB device configuration based on
the available driver support, and select the configuration with the
highest score. This will allow us to prefer ECM over RNDIS (for
devices which support both) and will allow us to meaningfully select a
configuration even when we have drivers available for all functions
(e.g. when exposing unused functions via EFI_USB_IO_PROTOCOL).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The decision on whether or not a zero-length packet needs to be
transmitted is independent of the host controller and belongs in the
USB core.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
TCP/IP checksum fields are one's complement values and therefore have
two possible representations of zero: positive zero (0x0000) and
negative zero (0xffff).
In RFC768, UDP over IPv4 exploits this redundancy to repurpose the
positive representation of zero (0x0000) to mean "no checksum
calculated"; checksums are optional for UDP over IPv4.
In RFC2460, checksums are made mandatory for UDP over IPv4. The
wording of the RFC is such that the UDP header is mandated to use only
the negative representation of zero (0xffff), rather than simply
requiring the checksum to be correct but allowing for either
representation of zero to be used.
In RFC1071, an example algorithm is given for calculating the TCP/IP
checksum. This algorithm happens to produce only the positive
representation of zero (0x0000); this is an artifact of the way that
unsigned arithmetic is used to calculate a signed one's complement
sum (and its final negation).
A common misconception has developed (exemplified in RFC1624) that
this artifact is part of the specification. Many people have assumed
that the checksum field should never contain the negative
representation of zero (0xffff).
A sensible receiver will calculate the checksum over the whole packet
and verify that the result is zero (in whichever representation of
zero happens to be generated by the receiver's algorithm). Such a
receiver will not care which representation of zero happens to be used
in the checksum field.
However, there are receivers in existence which will verify the
received checksum the hard way: by calculating the checksum over the
remainder of the packet and comparing the result against the checksum
field. If the representation of zero used by the receiver's algorithm
does not match the representation of zero used by the transmitter (and
so placed in the checksum field), and if the receiver does not
explicitly allow for both representations to compare as equal, then
the receiver may reject packets with a valid checksum.
For UDP, the combined RFCs effectively mandate that we should generate
only the negative representation of zero in the checksum field.
For IP, TCP and ICMP, the RFCs do not mandate which representation of
zero should be used, but the misconceptions which have grown up around
RFC1071 and RFC1624 suggest that it would be least surprising to
generate only the positive representation of zero in the checksum
field.
Fix by ensuring that all of our checksum algorithms generate only the
positive representation of zero, and explicitly inverting this in the
case of transmitted UDP packets.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Tested-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow iPXE to coexist with other USB device drivers, by attaching to
the EFI_USB_IO_PROTOCOL instances provided by the UEFI platform
firmware.
The EFI_USB_IO_PROTOCOL is an unsurprisingly badly designed
abstraction of a USB device. The poor design choices intrinsic in the
UEFI specification prevent efficient operation as a network device,
with the result that devices operated using the EFI_USB_IO_PROTOCOL
operate approximately two orders of magnitude slower than devices
operated using our native EHCI or xHCI host controller drivers.
Since the performance is so abysmally slow, and since the underlying
problems are due to fundamental architectural mistakes in the UEFI
specification, support for the EFI_USB_IO_PROTOCOL host controller
driver is left as disabled by default. Users are advised to use the
native iPXE host controller drivers instead.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Many UEFI NBPs expect to find an EFI_PXE_BASE_CODE_PROTOCOL installed
in addition to the EFI_SIMPLE_NETWORK_PROTOCOL. Most NBPs use the
EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the cached DHCP packets.
This implementation has been tested with grub.efi, shim.efi,
syslinux.efi, and wdsmgfw.efi. Some methods (such as Discover() and
Arp()) are not used by any known NBP and so have not (yet) been
implemented.
Usage notes for the tested bootstraps are:
- grub.efi uses EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the
cached DHCP packet, and uses no other methods.
- shim.efi uses EFI_PXE_BASE_CODE_PROTOCOL to retrieve the cached
DHCP packet and to retrieve the next NBP via the Mtftp() method.
If shim.efi was downloaded via HTTP (or other non-TFTP protocol)
then shim.efi will blindly call Mtftp() with an HTTP URI as the
filename: this allows the next NBP (e.g. grubx64.efi) to also be
transparently retrieved by HTTP.
shim.efi can also use the EFI_SIMPLE_FILE_SYSTEM_PROTOCOL to
retrieve files previously loaded by "imgfetch" or similar commands
in iPXE. The current implementation of shim.efi will use the
EFI_SIMPLE_FILE_SYSTEM_PROTOCOL only if it does not find an
EFI_PXE_BASE_CODE_PROTOCOL; this patch therefore prevents this
usage of our EFI_SIMPLE_FILE_SYSTEM_PROTOCOL. This logic could be
trivially reversed in shim.efi if needed.
- syslinux.efi uses EFI_PXE_BASE_CODE_PROTOCOL only to retrieve the
cached DHCP packet. Versions 6.03 and earlier have a bug which
may cause syslinux.efi to attach to the wrong NIC if there are
multiple NICs in the system (or if the UEFI firmware supports
IPv6).
- wdsmgfw.efi (ab)uses EFI_PXE_BASE_CODE_PROTOCOL to retrieve the
cached DHCP packets, and to send and retrieve UDP packets via the
UdpWrite() and UdpRead() methods. (This was presumably done in
order to minimise the amount of benefit obtainable by switching to
UEFI, by replicating all of the design mistakes present in the
original PXE specification.)
The EFI_DOWNGRADE_UX configuration option remains available for now,
until this implementation has received more widespread testing.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Merge the functionality of parse_next_server_and_filename() and
tftp_uri() into a single pxe_uri(), which takes a server address
(IPv4/IPv6/none) and a filename, and produces a URI using the rule:
- if the filename is a hierarchical absolute URI (i.e. includes a
scheme such as "http://" or "tftp://") then use that URI and ignore
the server address,
- otherwise, if the server address is recognised (according to
sa_family) then construct a TFTP URI based on the server address,
port, and filename
- otherwise fail.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently do not populate the ciaddr field in the constructed PXE
Boot Server ACK packet. This causes a WDS server to respond with a
broadcast packet, which is then ignored by wdsmgfw.efi since it does
not match the specified IP address filter.
Fix by populating ciaddr within the constructed PXE Boot Server ACK
packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Our SNP ReceiveFilters() method is a no-op, since we always (if
possible) use promiscuous mode for all network cards. The method
currently returns EFI_NOT_READY if the SNP interfaces are claimed for
use by iPXE, as with all other SNP methods.
The WDS bootstrap wdsmgfw.efi attempts to use both the PXE Base Code
protocol and the Simple Network Protocol simultaneously. This is
fundamentally broken, since use of the PXE Base Code protocol requires
us to disable the use of SNP (by claiming the interfaces for use by
iPXE), otherwise MnpDxe swallows all of the received packets before
our PXE Base Code's UdpRead() method is able to return them.
The root cause of this problem is that, as with BIOS PXE, the network
booting portions of the UEFI specification are less of a specification
and more of an application note sketchily describing how the original
hacked-together Intel implementation works. No sane design would ever
have included the UdpWrite() and UdpRead() methods.
Work around these fundamental conceptual flaws by unconditionally
returning success from efi_snp_receive_filters().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some distributions (observed with Ubuntu 15.04) place ldlinux.c32 in a
separate directory from isolinux.bin. Search for these files
separately, and allow an alternative location of ldlinux.c32 to be
provided via LDLINUX_C32=... on the make command line.
Reported-by: Adrian Koshka <adriankoshcha@teknik.io>
Tested-by: Adrian Koshka <adriankoshcha@teknik.io>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The debug directory size specified in the data directory should cover
only the EFI_IMAGE_DEBUG_DIRECTORY_ENTRY structure, not the whole of
the .debug section.
Reported-by: Andreas Hammarskjöld <junior@2PintSoftware.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add definitions of protocols observed to be used by wdsmgfw.efi, and
add a handle name type for ConIn, ConOut, and StdErr.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit edf74df ("[pxe] Always reconstruct packet for
PXENV_GET_CACHED_INFO") fixed the problems caused by returning stale
DHCP packets (e.g. from an earlier boot attempt using a different
network device), but broke interoperability with NBPs such as WDS
which may overwrite our cached (fake) DHCP packets and expect the
modified packets to be returned by a subsequent call to
PXENV_GET_CACHED_INFO.
Fix by constructing the fake DHCP packets immediately before
transferring control to a PXE NBP. Calls to PXENV_GET_CACHED_INFO
will now never modify the cached packets.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add debug wrappers for more boot services functions, and print
symbolic values rather than raw numbers where possible.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The raw EFI_HANDLE value is almost never useful to know, and simply
adds noise to the already verbose debug messages. Improve the
legibility of debug messages by using only the name generated by
efi_handle_name().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We attempt to mimic the behaviour of Intel's PXE ROM by skipping the
separate ProxyDHCPREQUEST if the ProxyDHCPOFFER already contains a
boot filename or a PXE boot menu.
Experimentation reveals that Intel's PXE ROM will also check for a
non-empty next-server address alongside the boot filename. Update our
test to match this behaviour.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Tested-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Commit 09b057c ("[settings] Remove "uristring" setting type") removed
support for URI-encoded settings via the "uristring" setting type, on
the basis that such encoding was no longer necessary to avoid problems
with the command line parser.
Other valid use cases for the "uristring" setting type do exist: for
example, a password containing a '/' character expanded via
chain http://username:${password:uristring}@server.name/boot.php
Restore the existence of the "uristring" setting, avoiding the
potentially large stack allocations that were used in the old code
prior to commit 09b057c ("[settings] Remove "uristring" setting
type").
Requested-by: Robin Smidsrød <robin@smidsrod.no>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When booting without an embedded script, display the imgstat()
information immediately before executing the downloaded image. This
allows potentially useful diagnostic information (such as the detected
image type) to be observed by the user without needing to enter the
iPXE shell and manually download the image.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current usage pattern of image_probe() is a legacy from the time
before commit 34b6ecb ("[image] Simplify image management") when
loading an image to its executable location in memory was a separate
action from actually executing the image.
Call image_probe() as soon as an image is registered. This allows
"imgstat" to display image type information for all images and allows
image-consuming code to assume that image->type is already set
correctly.
Ignore failures if image_probe() does not recognise the image, since
we do expect to handle unrecognised images (initrds, modules, etc).
Unrecognised images will be left with a NULL image->type, which
image-consuming code can easily check.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow the return status from an embedded image to propagate out to the
eventual return status from main(). When running under Linux, this
allows the pass/fail result of unit tests to be observable without
having to visually inspect the console output.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
A relatively common user mistake is to attempt to boot an EFI
executable (such as grub.efi) using a BIOS version of iPXE.
Unfortunately there are no signature checks that we can use to
unambiguously identify a PXE NBP, since a PXE NBP is just raw machine
code. We therefore have to accept anything sufficiently small to fit
into base memory as a valid PXE NBP.
We can detect that a file might be an EFI executable by checking for
the initial "MZ" signature bytes. This does not necessarily preclude
the file from also being a PXE NBP (since it would be possible to
create a hybrid binary which acts as both an EFI executable and a PXE
NBP, similar to the way in which wimboot and the Linux kernel are
hybrid binaries which act as both an EFI executable and a bzImage).
If the initial "MZ" signature bytes are present, then attempt to warn
the user by setting the image type to "PXE-NBP (may be EFI?)". We
can't (sensibly) prevent the user from accidentally running an EFI
executable as a PXE NBP, but we can at least make it easier for the
user to identify their mistake.
Inspired-by: Robin Smidsrød <robin@smidsrod.no>
Inspired-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Some ProxyDHCP servers and PXE boot servers do not specify a DHCP
server identifier via option 54. We currently work around this in a
variety of ad-hoc ways:
- if a ProxyDHCPACK has no server identifier then we treat it as
having the correct server identifier,
- if a boot server ACK has no server identifier then we use the
packet's source IP address as the server identifier.
Introduce the concept of a DHCP server pseudo-identifier, defined as
being:
- the server identifier (option 54), or
- if there is no server identifier, then the next-server address
(siaddr),
- if there is no server identifier or next-server address, then the
DHCP packet's source IP address.
Use the pseudo-identifier in place of the server identifier when
handling ProxyDHCP and PXE boot server responses.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The Infiniband link status change callback ipoib_link_state_changed()
may be called while the IPoIB device is closed, in which case there
will not be an IPoIB queue pair to be joined to the IPv4 broadcast
group. This leads to NULL pointer dereferences in ib_mcast_attach()
and ib_mcast_detach().
Fix by not attempting to join (or leave) the broadcast group unless we
actually have an IPoIB queue pair.
Signed-off-by: Wissam Shoukair <wissams@mellanox.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Rewrite the HTTP core to allow for the addition of arbitrary content
encoding mechanisms, such as PeerDist and gzip.
The core now exposes http_open() which can be used to create requests
with an explicitly selected HTTP method, an optional requested content
range, and an optional request body. A simple wrapper provides the
preexisting behaviour of creating either a GET request or an
application/x-www-form-urlencoded POST request (if the URI includes
parameters).
The HTTP SAN interface is now implemented using the generic block
device translator. Individual blocks are requested using http_open()
to create a range request.
Server connections are now managed via a connection pool; this allows
for multiple requests to the same server (e.g. for SAN blocks) to be
completely unaware of each other. Repeated HTTPS connections to the
same server can reuse a pooled connection, avoiding the per-connection
overhead of establishing a TLS session (which can take several seconds
if using a client certificate).
Support for HTTP SAN booting and for the Basic and Digest
authentication schemes is now optional and can be controlled via the
SANBOOT_PROTO_HTTP, HTTP_AUTH_BASIC, and HTTP_AUTH_DIGEST build
configuration options in config/general.h.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
UEFI platforms may provide a watchdog timer, which will reboot the
machine if an operating system takes more than five minutes to load.
This can cause long-lived iPXE downloads (or interactive shell
sessions) to unexpectedly reboot.
Fix by resetting the watchdog timer every ten seconds while the iPXE
main processing loop continues to run.
Reported-by: Bradley B Williams <bradleybwilliams@swbell.net>
Reported-by: John Clark <john.r.clark.3@gmail.com>
Reported-by: wdriever@gmail.com
Reported-by: Charlie Beima <cbeima@indiana.edu>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add support for SHA-224, SHA-384, and SHA-512 as digest algorithms in
X.509 certificates, and allow the choice of public-key, cipher, and
digest algorithms to be configured at build time via config/crypto.h.
Originally-implemented-by: Tufan Karadere <tufank@gmail.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The current implementation handles big-endian 24-bit integers (which
occur in several TLS record types) by treating them as big-endian
32-bit integers which are shifted by 8 bits. This can result in
"Invalid read" errors when running under valgrind, if the 24-bit field
happens to be exactly at the end of an I/O buffer.
Fix by ensuring that we touch only the three bytes which comprise the
24-bit integer.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Check for existence of the UART in uart_select(), not just in
uart_init(). This allows uart_select() to refuse to set a non-working
address in uart->base, which in turns means that the serial console
code will not attempt to use a non-existent UART.
Reported-by: Torgeir Wulfsberg <Torgeir.Wulfsberg@kongsberg.com>
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When the ability for iPXE to handle multiple serial ports was added,
the choice was made that the singular serial port referred to by
COMBOOT calls should mean the port used for the serial console. This
unintentionally caused IMAGE_COMBOOT to also enable CONSOLE_SERIAL.
Fix by providing a weak-symbol version of the serial console which
will be used if serial console support was not explicitly enabled.
Reported-by: Torgeir Wulfsberg <Torgeir.Wulfsberg@kongsberg.com>
Reported-by: Ján ONDREJ (SAL) <ondrejj@salstar.sk>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We do not set up any kind of virtual addressing before invoking an
ELFBoot image. Reject if the image's program headers indicate that
virtual addresses are not equal to physical addresses.
This avoids problems when loading some RHEL5 kernels, which seem to
include ELFBoot headers using virtual addressing. With this change,
these kernels are no longer detected as ELFBoot, and so may be
(correctly) detected as bzImage instead.
Reported-by: Torgeir.Wulfsberg@kongsberg.com
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Allow line buffer to accumulate multiple lines, with buffered_line()
returning each freshly-completed line as it is encountered. This
allows buffered lines to be subsequently processed as a group.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
VLAN and 802.11 devices use a network device operations structure that
wraps an underlying structure. For example, the vlan_operations
structure wraps the network device operations structure of the
underlying trunk device. This can cause false positives from the
current implementation of netdev_irq_supported(), which will always
report that VLAN devices support interrupts since it has no visibility
into the support provided by the underlying trunk device.
Fix by allowing network devices to explicitly flag that interrupts are
not supported, despite the presence of an irq() method.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iscsi_tx_done() is missing "break" statements at the end of each case.
(Fortunately, this happens not to cause a bug in practice, since
iscsi_login_request_done() is effectively a no-op when completing a
data-out PDU.)
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Extend the IPv6 concept of "scope ID" (indicating the network device
index) to IPv4 socket addresses, so that IPv4 multicast transmissions
may specify the transmitting network device.
The scope ID is not (currently) exposed via the string representation
of the socket address, since IPv4 does not use the IPv6 concept of
link-local addresses (which could legitimately be specified in a URI).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Redefine various IPv4 address constants and testing macros to avoid
unnecessary byte swapping at runtime, and slightly rename the macros
to prevent code from accidentally using the old definitions.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid using zero as a network device index, so that a zero
sin6_scope_id can be used to mean "unspecified" (rather than
unintentionally meaning "net0").
Signed-off-by: Michael Brown <mcb30@ipxe.org>
When an IPv6 socket address string specifies a link-local or multicast
address but does not specify the requisite network device name
(e.g. "fe80::69ff:fe50:5845" rather than "fe80::69ff:fe50:5845%net0"),
assume the use of "netX".
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Remove AXTLS headers now that no AXTLS code remains, with many thanks
to the AXTLS project for use of their cryptography code over the past
several years.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Replace the AES implementation from AXTLS with a dedicated iPXE
implementation which is slightly smaller and around 1000% faster.
This implementation has been verified using the existing self-tests
based on the NIST AES test vectors.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Generalise the existing support for performing CBC-mode block cipher
tests, and update the code to use okx() for neater reporting of test
results.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
xfer_buffer() uses intf_get_dest_op() to obtain the destination
interface for xfer_deliver(), in order to check that this is the same
interface which provides xfer_buffer(). The return value from
intf_get_dest_op() (which contains the actual method implementing
xfer_deliver()) is not used.
On some gcc versions, this triggers a "value computed is not used"
warning, since the explicit type cast included within the
intf_get_dest_op() macro is treated as a "value computed".
Fix by explicitly casting the result of intf_get_dest_op() to void.
Reported-by: Matthew Helton <mwhelton@gmail.com>
Reported-by: James A. Peltier <jpeltier@sfu.ca>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reduce the cost of implementing object methods which convey no
information beyond the fact that the method has been called.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide profile_custom() as a trivial wrapper around profile_update()
to allow for the use of the profiling infrastructure by code using
timers other than the default profile_timestamp() provider.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide an inject_corruption() function that can be used to randomly
corrupt data bytes with configurable probabilities.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Provide a generic inject_fault() function that can be used to inject
random faults with configurable probabilities.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Add a named configuration for qemu, based on the config.ipxe.general.h
file taken from the current qemu repository and enabling the option to
work around the missing EFI_PXE_BASE_CODE_PROTOCOL.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
iPXE does not currently provide EFI_PXE_BASE_CODE_PROTOCOL: this
causes failures when chainloading bootloaders such as shim.efi which
assume that this protocol will be present.
Provide the ability to work around these problems via the build
configuration option EFI_DOWNGRADE_UX. If this option is enabled,
then we will not install our usual EFI_LOAD_FILE_PROTOCOL
implementation, thereby allowing the platform firmware to install its
own EFI_PXE_BASE_CODE_PROTOCOL implementation on top of our
EFI_SIMPLE_NETWORK_PROTOCOL handle.
A somewhat major side-effect of this workaround is that almost all
iPXE features will be disabled.
This configuration option will be removed in future when support for
EFI_PXE_BASE_CODE_PROTOCOL is added.
Requested-by: Laszlo Ersek <lersek@redhat.com>
Requested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Fix the TxBuf value filled in by GetStatus() to report the transmit
buffer address as required by the (now clarified) specification.
Simplify "interrupt" handling in GetStatus() to report only that one
or more packets have been transmitted or received; there is no need to
report one GetStatus() "interrupt" per packet.
Simplify receive handling to dequeue received packets immediately from
the network device into an internal list (thereby avoiding the hacks
previously used to determine when to report new packet arrivals).
Originally-fixed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Expose the high bit of the VGA text attribute byte via the ANSI SGR
parameters 5 ("blink on") and 25 ("blink off").
Note that some video cards (and virtual machines) may display a high
intensity background colour instead of blinking text.
Signed-off-by: Christian Nilsson <nikize@gmail.com>
Modified-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Multicast MAC addresses will never have REMAC cache entries, and the
corresponding multicast IPoIB MAC address cannot be obtained simply by
issuing an ARP request.
For the trivial volume of multicast packets that we expect to send in
any realistic scenario, the simplest solution is to send them as
broadcasts instead.
Reported-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
We currently do not wait for a received FIN before exiting to boot a
loaded OS. In the common case of booting from an HTTP server, this
means that the TCP connection is left consuming resources on the
server side: the server will retransmit the FIN several times before
giving up.
Fix by initiating a graceful close of all TCP connections and waiting
(for up to one second) for all connections to finish closing
gracefully (i.e. for the outgoing FIN to have been sent and ACKed, and
for the incoming FIN to have been received and ACKed at least once).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Older, out-of-tree Xen kernel modules (such as those provided with
SuSE Linux Enterprise Server 11) do not clear the leftover "event
pending" bit when opening an event channel. Consequently, no event is
ever delivered to indicate that there is information in the XenStore
ring buffer, and the system hangs shortly after loading the
xen-platform-pci kernel module.
Work around this problem by always waiting for the XenStore event
channel to be signalled, and clearing the event before processing the
received data.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
The only way to map an eIPoIB MAC address (REMAC) to an IPoIB MAC
address is to intercept an incoming ARP request or reply.
If we do not have an REMAC cache entry for a particular destination
MAC address, then we cannot transmit the packet. This can arise in at
least two situations:
- An external program (e.g. a PXE NBP using the UNDI API) may attempt
to transmit to a destination MAC address that has been obtained by
some method other than ARP.
- Memory pressure may have caused REMAC cache entries to be
discarded. This is fairly likely on a busy network, since REMAC
cache entries are created for all received (broadcast) ARP
requests. (We can't sensibly avoid creating these cache entries,
since they are required in order to send an ARP reply, and when we
are being used via the UNDI API we may have no knowledge of which
IP addresses are "ours".)
Attempt to ameliorate the situation by generating a semi-spurious ARP
request whenever we find a missing REMAC cache entry. This will
hopefully trigger an ARP reply, which would then provide us with the
information required to populate the REMAC cache.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
As with the neighbour cache, discarding an REMAC cache entry is
potentially very disruptive.
Originally-fixed-by: Wissam Shoukair <wissams@mellanox.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Avoid accidentally returning stale packets (e.g. for a previously
attempted network device) by always constructing a fresh DHCP packet.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
If the link is blocked (e.g. due to a Spanning Tree Protocol port not
yet forwarding packets) then defer DHCP discovery until the link
becomes unblocked.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
