init_fix_up
This commit is contained in:
Udayan Kumar
parent
751cb2e450
commit
334abbde83
|
|
@ -79,6 +79,7 @@
|
|||
#include <gpxe/spi_bit.h>
|
||||
#include <gpxe/threewire.h>
|
||||
#include <gpxe/nvo.h>
|
||||
#include <mii.h>
|
||||
|
||||
#define TX_RING_SIZE 4
|
||||
#define NUM_RX_DESC 4
|
||||
|
|
@ -122,6 +123,28 @@ struct natsemi_nic {
|
|||
struct nvo_block nvo;
|
||||
};
|
||||
|
||||
|
||||
/*
|
||||
* Support for fibre connections on Am79C874:
|
||||
* This phy needs a special setup when connected to a fibre cable.
|
||||
* http://www.amd.com/files/connectivitysolutions/networking/archivednetworking/22235.pdf
|
||||
*/
|
||||
#define PHYID_AM79C874 0x0022561b
|
||||
|
||||
enum {
|
||||
MII_MCTRL = 0x15, /* mode control register */
|
||||
MII_FX_SEL = 0x0001, /* 100BASE-FX (fiber) */
|
||||
MII_EN_SCRM = 0x0004, /* enable scrambler (tp) */
|
||||
};
|
||||
|
||||
|
||||
|
||||
/* values we might find in the silicon revision register */
|
||||
#define SRR_DP83815_C 0x0302
|
||||
#define SRR_DP83815_D 0x0403
|
||||
#define SRR_DP83816_A4 0x0504
|
||||
#define SRR_DP83816_A5 0x0505
|
||||
|
||||
/* NATSEMI: Offsets to the device registers.
|
||||
* Unlike software-only systems, device drivers interact with complex hardware.
|
||||
* It's not useful to define symbolic names for every register bit in the
|
||||
|
|
@ -351,6 +374,143 @@ static void nat_reset ( struct natsemi_nic *nat ) {
|
|||
outl ( SavedClkRun, nat->ioaddr + ClkRun );
|
||||
}
|
||||
|
||||
|
||||
static int mdio_read(struct net_device *netdev, int reg) {
|
||||
struct natsemi_nic *nat = netdev->priv;
|
||||
|
||||
/* The 83815 series has two ports:
|
||||
* - an internal transceiver
|
||||
* - an external mii bus
|
||||
*/
|
||||
return inw(nat->ioaddr+BasicControl+(reg<<2));
|
||||
}
|
||||
|
||||
static void mdio_write(struct net_device *netdev, int reg, u16 data) {
|
||||
struct natsemi_nic *nat = netdev->priv;
|
||||
|
||||
/* The 83815 series has an internal transceiver; handle separately */
|
||||
writew(data, nat->ioaddr+BasicControl+(reg<<2));
|
||||
}
|
||||
|
||||
static void init_phy_fixup(struct net_device *netdev) {
|
||||
struct natsemi_nic *nat = netdev->priv;
|
||||
int i;
|
||||
u32 cfg;
|
||||
u16 tmp;
|
||||
uint16_t advertising;
|
||||
int mii;
|
||||
|
||||
/* restore stuff lost when power was out */
|
||||
tmp = mdio_read(netdev, MII_BMCR);
|
||||
advertising= mdio_read(netdev, MII_ADVERTISE);
|
||||
// if (np->autoneg == AUTONEG_ENABLE) {
|
||||
/* renegotiate if something changed */
|
||||
if ((tmp & BMCR_ANENABLE) == 0
|
||||
|| advertising != mdio_read(netdev, MII_ADVERTISE))
|
||||
{
|
||||
/* turn on autonegotiation and force negotiation */
|
||||
tmp |= (BMCR_ANENABLE | BMCR_ANRESTART);
|
||||
mdio_write(netdev, MII_ADVERTISE, advertising);
|
||||
}
|
||||
// } else {
|
||||
/* turn off auto negotiation, set speed and duplexity */
|
||||
// tmp &= ~(BMCR_ANENABLE | BMCR_SPEED100 | BMCR_FULLDPLX);
|
||||
// if (np->speed == SPEED_100)
|
||||
/// tmp |= BMCR_SPEED100;
|
||||
// if (np->duplex == DUPLEX_FULL)
|
||||
// tmp |= BMCR_FULLDPLX;
|
||||
/*
|
||||
* Note: there is no good way to inform the link partner
|
||||
* that our capabilities changed. The user has to unplug
|
||||
* and replug the network cable after some changes, e.g.
|
||||
* after switching from 10HD, autoneg off to 100 HD,
|
||||
* autoneg off.
|
||||
*/
|
||||
// }
|
||||
mdio_write(netdev, MII_BMCR, tmp);
|
||||
inl(nat->ioaddr + ChipConfig);
|
||||
udelay(1);
|
||||
|
||||
/* find out what phy this is */
|
||||
mii = (mdio_read(netdev, MII_PHYSID1) << 16)
|
||||
+ mdio_read(netdev, MII_PHYSID2);
|
||||
|
||||
/* handle external phys here */
|
||||
switch (mii) {
|
||||
case PHYID_AM79C874:
|
||||
/* phy specific configuration for fibre/tp operation */
|
||||
tmp = mdio_read(netdev, MII_MCTRL);
|
||||
tmp &= ~(MII_FX_SEL | MII_EN_SCRM);
|
||||
//if (dev->if_port == PORT_FIBRE)
|
||||
// tmp |= MII_FX_SEL;
|
||||
//else
|
||||
tmp |= MII_EN_SCRM;
|
||||
mdio_write(netdev, MII_MCTRL, tmp);
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
cfg = inl(nat->ioaddr + ChipConfig);
|
||||
if (cfg & CfgExtPhy)
|
||||
return;
|
||||
|
||||
/* On page 78 of the spec, they recommend some settings for "optimum
|
||||
performance" to be done in sequence. These settings optimize some
|
||||
of the 100Mbit autodetection circuitry. They say we only want to
|
||||
do this for rev C of the chip, but engineers at NSC (Bradley
|
||||
Kennedy) recommends always setting them. If you don't, you get
|
||||
errors on some autonegotiations that make the device unusable.
|
||||
|
||||
It seems that the DSP needs a few usec to reinitialize after
|
||||
the start of the phy. Just retry writing these values until they
|
||||
stick.
|
||||
*/
|
||||
uint32_t srr = inl(nat->ioaddr + SiliconRev);
|
||||
int NATSEMI_HW_TIMEOUT = 400;
|
||||
for (i=0;i<NATSEMI_HW_TIMEOUT;i++) {
|
||||
|
||||
int dspcfg,dspcfg_1;
|
||||
outw(1, nat->ioaddr + PGSEL);
|
||||
outw(PMDCSR_VAL, nat->ioaddr + PMDCSR);
|
||||
outw(TSTDAT_VAL, nat->ioaddr + TSTDAT);
|
||||
dspcfg = (srr <= SRR_DP83815_C)?
|
||||
DSPCFG_VAL : (DSPCFG_COEF | readw(nat->ioaddr + DSPCFG));
|
||||
outw(dspcfg, nat->ioaddr + DSPCFG);
|
||||
outw(SDCFG_VAL, nat->ioaddr + SDCFG);
|
||||
outw(0, nat->ioaddr + PGSEL);
|
||||
inl(nat->ioaddr + ChipConfig);
|
||||
udelay(10);
|
||||
|
||||
outw(1, nat->ioaddr + PGSEL);
|
||||
dspcfg_1 = readw(nat->ioaddr + DSPCFG);
|
||||
outw(0, nat->ioaddr + PGSEL);
|
||||
if (dspcfg == dspcfg_1)
|
||||
break;
|
||||
}
|
||||
|
||||
if (i==NATSEMI_HW_TIMEOUT) {
|
||||
DBG ( "Natsemi: DSPCFG mismatch after retrying for"
|
||||
" %d usec.\n", i*10);
|
||||
} else {
|
||||
DBG ( "NATSEMI: DSPCFG accepted after %d usec.\n",
|
||||
i*10);
|
||||
}
|
||||
/*
|
||||
* Enable PHY Specific event based interrupts. Link state change
|
||||
* and Auto-Negotiation Completion are among the affected.
|
||||
* Read the intr status to clear it (needed for wake events).
|
||||
*/
|
||||
inw(nat->ioaddr + MIntrStatus);
|
||||
//MICRIntEn = 0x2
|
||||
outw(0x2, nat->ioaddr + MIntrCtrl);
|
||||
}
|
||||
|
||||
|
||||
/*
|
||||
* Patch up for fixing CRC errors.
|
||||
* adapted from linux natsemi driver
|
||||
*
|
||||
*/
|
||||
static void do_cable_magic ( struct net_device *netdev ) {
|
||||
struct natsemi_nic *nat = netdev->priv;
|
||||
uint16_t data;
|
||||
|
|
@ -478,6 +638,7 @@ static int nat_open ( struct net_device *netdev ) {
|
|||
* testing this feature is required or not
|
||||
*/
|
||||
do_cable_magic ( netdev );
|
||||
init_phy_fixup ( netdev );
|
||||
|
||||
|
||||
/* mask the interrupts. note interrupt is not enabled here
|
||||
|
|
|
|||
Reference in New Issue